Motorline professional ROSSO EVO User'S And Installer'S Manual Download Page 2

2A

2B

2B

4A

4B

7A

10A

14A

15

16

18

5A

7B

10B

14B

17

5B

9

13B

14B

5B
6A
6A
6B

EN

EN

STANDARDS TO FOLLOW

INSIDE THE PACKAGE

TECHNICAL SPECIFICATIONS

ENGINE’S FIXATION IN THE PIPELINE 

LEGEND 

STOPPER AT THE OPENING

CONNECTING ENGINE TO 24V BATTERY

CONTROL BOARD ERROR MAP

ROSSO EVO CENTRAL

MANUAL BRAKE RELEASE

THE AUTOMATISM INSTALLATION 

MENU FUNCTIONS 

STRETCH RAIL CHAIN

INSTRUCTIONS FOR CONSUMERS | TECHNICAL PERSONNEL

REMOVE UPPER COVER

INSTALLATION MAP

PROGRAMMING TRANSMITTERS

MAINTENANCE 

REPLACE UPPER COVER
CHANGING  COURTESY  LEDS
CHANGING FUSE
PRE-INSTALLATION INFORMATION

01. SAFETY INSTRUCTIONS

02. PACKAGE

03. THE AUTOMATISM

04. INSTALLATION

05. PROGRAMMING

06. POST-INSTALLATION

07. DIAGNOSIS

08. TROUBLESHOOTING

09. CENTRAL CONNECTIONS

INDEX

STANDARDS TO FOLLOW

00. CONTENT

01. SAFETY INSTRUCTIONS

This product is certified in accordance with European 

Community (EC) safety standards.

This product complies with Directive 2011/65/EU of the 

European Parliament and of the Council, of 8 June 2011, on 

the restriction of the use of certain hazardous substances in 

electrical and electronic equipment.

(Applicable in countries with recycling systems).

This marking on the product or literature indicates that the 

product and electronic accessories (eg. Charger, USB cable, 

electronic material, controls, etc.) should not be disposed of 

as other household waste at the end of its useful life. To avoid 

possible harm to the environment or human health resulting 

from the uncontrolled disposal of waste, separate these items 

from other types of waste and recycle them responsibly to 

promote the sustainable reuse of material resources. Home 

users should contact the dealer where they purchased this 

product or the National Environment Agency for details on 

where and how they can take these items for environmentally 

safe recycling. Business users should contact their vendor and 

check the terms and conditions of the purchase agreement. 

This product and its electronic accessories should not be 

mixed with other commercial waste.

This marking indicates that the product and electronic accessories 

(eg. charger, USB cable, electronic material, controls, etc.) are 

susceptible to electric shock by direct or indirect contact with 

electricity. Be cautious when handling the product and observe 

all safety procedures in this manual.  

Summary of Contents for ROSSO EVO



















Reviews: