MOTO GUZZI Stelvio 1200 4V Service Station Manual Download

Page: 99 / 135

•

Bring the left cylinder piston to the TDC

in combustion phase.

•

Mark a reference on the oil pump con-

trol gear and another on the driven

gear so as to place them correctly

again upon refitting.

•

Unscrew and remove the nut on the

crankshaft.

•

Remove the oil pump control gear.

•

Screw the nut again so that the internal

shim washer does not fall in the crank-

shaft crankcase.

•

Unscrew and remove the driven gear

nut.

•

Collect the washer.

•

Remove the oil pump driven gear.

•

Remove the driving pin.

•

Undo and remove the three screws.

•

Remove the oil pump.

STELVIO 4V - 1200

Engine

ENG - 73

Summary of Contents for Stelvio 1200 4V








































































































































Search results

Summary of Contents for Stelvio 1200 4V

Reviews:

Related manuals for Stelvio 1200 4V

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 4V, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 4V

Reviews:

Related manuals for Stelvio 1200 4V

Brands by name

Popular brands