MOTO GUZZI Stelvio 1200 4V Service Station Manual Download

Page: 75 / 135

Cam timing

•

Fit the crankshaft and the service shaft

on the crankcase.

•

Fit the cylinders.

•

Turn the crankshaft until the left cylin-

der piston reaches the top dead centre

(TDC).

•

Fit the cotter and the shim washer on

the service shaft.

•

Fit the tone wheel with the chamfered

side facing the crankcase on the serv-

ice shaft.

•

Lock crankshaft rotation.

•

Unscrew and remove the nut fixing the

crankshaft gear.

•

Remove the oil pump control gear.

Specific tooling

12.91.18.01

Tool to lock flywheel and start-up

crown gear

•

Fit the timing system gear and align the

reference with that on the crankshaft

gear. Turn the crankshaft to align the

two gears.

STELVIO 4V - 1200

Engine

ENG - 49

Summary of Contents for Stelvio 1200 4V








































































































































Search results

Summary of Contents for Stelvio 1200 4V

Reviews:

Related manuals for Stelvio 1200 4V

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 4V, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 4V

Reviews:

Related manuals for Stelvio 1200 4V

Brands by name

Popular brands