MOTO GUZZI Stelvio 1200 4V Service Station Manual Download

Page: 82 / 135

•

Insert the pin.

•

Inserire il fermo dello spinotto.

Specific tooling

020470Y

Pin snap ring fitting tool

Installing the cylinder

RIGHT CYLINDER

•

Fit the piston.

•

Remove the cloth used to prevent for-

eign bodies from getting into the crank-

case.

•

Turn the rings so that the coupling ends

are 120 degrees from each other.

•

Place a new metal gasket between the

crankcase and the cylinder. Place the

two dowel pins on the stud bolts. Lu-

bricate the piston and the cylinder.

Lock connecting rod motion with the

fork tool. Using the suitable piston ring

clamp tool, place the cylinder and fit the

chain in the timing system plate.

CAUTION

DURING THIS OPERATION, PAY ATTENTION
NOT TO DAMAGE THE PISTON.

Specific tooling

Engine

STELVIO 4V - 1200

ENG - 56

Summary of Contents for Stelvio 1200 4V








































































































































Search results

Summary of Contents for Stelvio 1200 4V

Reviews:

Related manuals for Stelvio 1200 4V

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 4V, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 4V

Reviews:

Related manuals for Stelvio 1200 4V

Brands by name

Popular brands