Monmouth Scientific Cleanroom Kit 4M Installation Manual Download Page 48 | Manualshive

Page: 48 / 72

background image

Issue 03 – June 2018

48

CAM1000

Introduction

CAUTION: Weight approximately 40kg. Follow all correct lifting
techniques. Use lifting equipment when handling.

The CAM1000 units are self-contained filtration units designed to fit into the aluminium grid system
with your cleanroom. On spans of 3m or more, they will sit in between the larger reinforced ceiling
cross members.

They are designed to be used on their own, however if you do wish to connect two or more together
then up to 4 units can be daisy-chained from the IEC socket mounted on the side of the unit. If not
used to power a second CAM1000, then this socket can be used to power the lights in the room. This
way they are all turned on and off by a single switch.

Power Link Socket

Link Fuse Holder 3A(T)

Power Inlet Socket

Main Inlet Fuse

Power Switch

IMPORTANT: The loading on the whole system MUST NOT exceed 3amps in total. If in doubt
consult a qualified electrician.

The power switch above is an inline switch that requires a power supply. All the CAM1000
units and/or lights subsequent to this will be fed from this switch.

«
...
46
47
48
49
50
...
»

Summary of Contents for Cleanroom Kit 4M









































































Reviews:

No comments

Related manuals for Cleanroom Kit 4M

Brand: Taber Pages: 27

Brand: Odom Pages: 19

Brand: MacDon Pages: 30

Brand: idi Pages: 20

Brand: G&G Pages: 2

Brand: H&S Pages: 46

Brand: Life Fitness Pages: 45

VADA TWIN MOTOR MACERATOR

Brand: Reece Pages: 7

Brand: Econo-Wrap Pages: 27

Brand: endolite Pages: 158

Brand: Lupine Pages: 7

Brand: Blizzard Lighting Pages: 24

Brand: Sima Pages: 22

AeroX Audio 105

Brand: Campbell Pages: 23

Brand: ACS Pages: 23

Brand: Gearmore Pages: 24

Brand: National Instruments Pages: 21

Brand: Future light Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands