Miyachi Unitek LMV700 Operator'S Manual Download Page 21

Page: 21 / 72

CHAPTER 1: SYSTEM DESCRIPTION

LMV700 Nd:YVO

LASER MARKER

990-545

1-9

Included Accessories

The following accessories are provided with the product:

Component Quantity

Cleaning paper

Protective eyewear

Hex wrench (for M4 hex screws)

Marking program

Operation Manuals (990-545 and 990-546)

1 ea.

Laser Safety Manual (990-502)

Wrench (for fiber connectors)

Options

The following items are available as options:

Component Description

Protective glass

The Marker is shipped with a protective glass affixed to the f-theta
lens. If this glass becomes soiled or cracked a replacement may be
purchased.

A new LD (diode for laser excitation).

LD restoration

When the LD fails to mark properly it may be sent in for
refurbishment. Once the LD is refurbished, it can be re-installed in
the marker.

Air filter (Oscillator)

An air filter is installed in the Oscillator at the time of purchase.

Air Filter (Control Unit)

An air filter is installed in the Control Unit at the time of purchase.

Graphite sheet

The graphite sheet allows the heat to transfer from the LD module
to the Peltier cooling device. When replacing an LD module, the
graphite sheet must be free from cracks or damage.

Lithium system battery

CR2450 (Backup battery for internal memory.)

USB cable

For communications with a computer.

Summary of Contents for LMV700









































































Search results

Summary of Contents for LMV700

Reviews:

Related manuals for LMV700

Brands by name

Popular brands

Miyachi Unitek LMV700, Operator'S Manual

Search results

Summary of Contents for LMV700

Reviews:

Related manuals for LMV700

Brands by name

Popular brands