Mitsubishi Electric Mr.Slim PUHZ-P100VKA Service Manual Download Page 80

Page: 80 / 111

OCH670

Test run

Input maintenance info.

Function setting

Check

Self check

Function setting

Cursor

Address

Monitor:

Ref. address

Unit No.

Grp.

/1/2/3/4/All

Function setting

Cursor

Request:

Ref. address

Mode 1

Mode 2

Mode 3

Mode 4

Grp.

Function setting

Cursor

Request:

Ref. address

Mode 1

Mode 2

Mode 3

Mode 4

Unit #1

Set the indoor unit refrigerant addresses and unit numbers with the F1
through F4 buttons, and then press the

button to confirm the current

setting.

Select "Function setting" with the F1 or F2 button, and press the

button.

When data collection from the indoor units is completed, the current settings

appears highlighted.

Non-highlighted items indicate that no function settings are made.

Screen appearance varies depending on the "Unit No." setting.

Use the F1 or F2 button to move the cursor to select the mode number,
and change the setting number with the F3 or F4 button.

Select "Service" from the Main menu, and press the

button.

<Checking the indoor unit No.>

When the

button is pressed, the target indoor unit will start fan operation.

If the unit is common or when running all units, all indoor units for the selected
refrigerant address will start fan operation.

Function setting

Ref. address

Sending data

Grp.

When the settings are completed, press the

button to send the setting

data from the remote controller to the indoor units.

When the transmission is successfully completed, the screen will return to the

Function setting screen.

Notes:

1. Make the above settings only on Mr. Slim units as necessary.

2. The above function settings are not available for the City Multi units.

3. Table 1 summarizes the setting options for each mode number. Refer to the

indoor unit Installation Manual for the detailed information about initial set-

tings, mode numbers, and setting numbers for the indoor units.

4. Be sure to write down the settings for all functions if any of the initial set-

tings has been changed after the completion of installation work.

<Function setting>

Summary of Contents for Mr.Slim PUHZ-P100VKA
















































































































Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Service Manual

Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands