Mitsubishi Electric Mr.Slim PUHZ-P100VKA Service Manual Download Page 103

Page: 103 / 111

103

OCH670

<Guide for opration condition>

Inspection item

Result

Power supply

Loose con-

nection

Breaker

Good

Retightened

Terminal block

Outdoor Unit

Good

Retightened

Indoor Unit

Good

Retightened

(Insulation resistance)

(Voltage)

Accumulated operating time

Time

Number of ON/OFF times

Times

Current

Refrigerant/heat exchanger temperature COOL

HEAT

Refrigerant/discharge temperature COOL

HEAT

Air/outside air temperature

COOL

HEAT

(Air/discharge temperature)

COOL

HEAT

Appearance

Good

Cleaning required

Heat exchanger

Good

Cleaning required

Sound/vibration

None

Present

Air/intake air temperature

COOL

HEAT

(Air/discharge temperature)

COOL

HEAT

Refrigerant/heat exchanger temperature COOL

HEAT

Filter operating time*

Time

Decorative panel

Good

Cleaning required

Filter

Good

Cleaning required

Fan

Good

Cleaning required

Heat exchanger

Good

Cleaning required

Sound/vibration

None

Present

Com-
pressor

Temperature

Cleanli- ness

Outdoor Unit

Temperature

Cleanliness

Indoor Unit

* The filter operating time is the time that has elapsed since the filter was reset.

Check Points

Enter the temperature differences between

and

into

the graph given below.

Operation state is determined according to the plotted areas on

the graph.

For data measurements, set the fan speed to "Hi" before activat-

ing maintenance mode.

Is "D000" displayed stably on the remote
controller?
(

Discharge temperature) – (

Outdoor

heat exchanger temperature)
(

Indoor intake air temperature) – (

Indoor heat exchanger temperature)
Is "D000" displayed stably on the remote
controller?
(

Discharge temperature) – (

Indoor

heat exchanger temperature)
(

Indoor heat exchanger temperature) –

(

Indoor intake air temperature)

Cool

Classification

Item

Result

Inspection

Temperature
difference

Heat

Inspection

Temperature
difference

Stable Unstable

* Fixed Hz operation may not be possible under the following tempera-

ture ranges.

A)In cool mode, outdoor intake air temperature is 40

or higher or

indoor intake air temperature is 23

or lower.

B)In heat mode, outdoor intake air temperature is 20

or higher or

indoor intake air temperature is 25

or lower.

* If the air conditioner is operated at a temperature range other than the

ones above but operation is not stabilized after 30 minutes or more have

elapsed, carry out inspection.

* In heat mode, the operation state may vary due to frost forming on the

outdoor heat exchanger.

0 10 20 30 40 50 60 70 80

Normal

Filter inspection

Inspection C

Inspection A

Inspection B

0 10 20 30 40 50 60 70 80

Normal

Filter inspection

Inspection C

Inspection A

Inspection B

Cool mode

Heat mode

(

Indoor intake air temperature)—

(

Indoor

heat exchang

er temperature)

(

Indoor heat exchanger temperature) —

(

Indoor intake air temperature)

[

Discharge temperature] – [

Outdoor

heat exchanger temperature)

[

Discharge temperature] – [

Indoor

heat exchanger temperature)

Result

Normal operation state
Filter may be clogged. *1
Performance has dropped. Detailed in-
spection is necessary.
Refrigerant amount is dropping.
Filter or indoor heat exchanger may be
clogged.

Area

Check item

Judgement

Cool

Heat

Normal
Filter inspection
Inspection A

Inspection B
Inspection C

The above judgement is just guide based on Japanese standard

conditions.

It may be changed depending on the indoor and outdoor

temperature.

It may be judged as "Filter inspection" due to the outdoor and

indoor temperature, even though it is not clogged.

Summary of Contents for Mr.Slim PUHZ-P100VKA
















































































































Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Service Manual

Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands