Mitsubishi Electric Mr.Slim PUHZ-P100VKA Service Manual Download Page 49

Page: 49 / 111

OCH670

198 V AC to 264 V AC?

Are there looseness or

disconnection of the indoor/

outdoor connecting wire?

Is anything displayed?

17 V DC to 28 V DC?

Is “E8” displayed?

Can all the indoor

unit be operated?

Check the voltage between S2

and S3 on the terminal block of

the outdoor unit.

YES

Not lighting.

Blinking.

YES

Not displayed.

Displayed.

YES

Check the voltage between S1 and S2 on the terminal block (TB4)

of the indoor unit which is used to connect the indoor unit and the

outdoor unit.

Check the refrigerant address of

the outdoor unit. (SW1-3 to 1-6)

Check the looseness or disconnection

of the indoor/outdoor connecting wire.

Check the LED display of the

outdoor unit after turning on the

main power again.

Can the unit be restarted?

•

Breaking or poor contact

of the indoor/outdoor

connecting wire

• Fix the breaking or poor

contact of the indoor/outdoor

connecting wire.

• Defective outdoor

controller circuit

board

• Replace the outdoor

controller circuit board.

• Normal.

Only the unit which

has the refrigerant

address “0” supplies

power to the remote

controller.

• Set the refrigerant

address to “0”. In case of

the multiple grouping

system, recheck the

refrigerant address again.

• Defective indoor

power board

• Replace the indoor

power board.

• Defective outdoor

power circuit board

• Replace the outdoor

power circuit board.

• Defective indoor

controller board

• Replace the indoor controller

board of the indoor unit which

does not operate.

• Defective outdoor

controller circuit

board

• Replace the outdoor

controller circuit board.

• Influence of

electromagnetic noise

• Not abnormal.

There may be the influence

of electromagnetic noise.

Check the transmission wire

and get rid of the causes.

Symptoms: Nothing is displayed on the remote controller

Diagnosis flow

Cause

Inspection method and

troubleshooting

LED display of the indoor

controller board

LED1 :

LED2 :

LED3 : or

Check the status

of the indoor controller

board LED3 display.

Is the refrigerant

address “0”?

YES

Is “EA” or “Eb”

displayed?

Summary of Contents for Mr.Slim PUHZ-P100VKA
















































































































Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Service Manual

Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands