Mitsubishi Electric Mr.Slim PUHZ-P100VKA Service Manual Download Page 44

Page: 44 / 111

OCH670

Check code

Abnormal points and detection method

Case

Judgment and action

(6607)

5. If displayed address or attribute is

FRESH MASTER, indoor unit detects

abnormality when indoor unit transmits

signal to FRESH MASTER and there

was no reply (ACK).

During sequential operation

of indoor unit and FRESH

MASTER of other refrigerant

system, if indoor unit transmits

signal to FRESH MASTER

while outdoor unit power sup-

ply of same refrigerant sys-

tem with FRESH MASTER is

turned off or within 2 minutes

of restart, abnormality is

detected.

Contact failure of transmission

wire of indoor unit or FRESH

MASTER

Disconnection of transmission

connector (CN2M) of indoor

unit or FRESH MASTER

Defective transmitting receiving

circuit of indoor unit or FRESH

MASTER

6. If displayed address or attribute is

LOSSNAY, indoor unit detects abnormal-

ity when indoor unit transmits signal to

LOSSNAY and there was no reply (ACK).

If the power supply of

LOSSNAY is off, indoor unit

detects abnormality when it

transmits signal to LOSSNAY.

During sequential operation

of indoor unit and LOSSNAY

of other refrigerant system, if

indoor unit transmits signal to

LOSSNAY while outdoor unit

power supply of same refrig-

erant system with LOSSNAY

is turned off or within 2 min-

utes of restart, abnormality is

detected.

Contact failure of transmis-

sion wire of indoor unit of

LOSSNAY

Disconnection of transmission

connector (CN2M) of indoor

unit

Defective transmitting receiv-

ing circuit of indoor unit or

LOSSNAY

7. If displayed address or attribute is non-

existent.

The unit of former address

does not exist as address

switch has changed while the

unit was energized.

Abnormality is detected

when indoor unit transmits

signal because the address

of FRESH MASTER and

LOSSNAY are changed after

sequential operation of FRESH

MASTER and LOSSNAY by

remote controller.

From the previous page.

4. If displayed address or attribute is

remote controller, indoor unit detects

abnormality when indoor unit transmits

signal to remote controller and there

was no reply (ACK).

During group operation with

indoor unit of multi- refrigerant

system, if indoor unit transmit

signal to remote controller

while outdoor unit power sup-

ply of one refrigerant system

is turned off or within 2 min-

utes of restart, abnormality is

detected.

Contact failure of transmission

wire of remote controller or

indoor unit

Disconnection of transmission

connector (CN2M) of indoor

unit

Defective transmitting receiving

circuit of indoor unit or remote

controller

Same as mentioned in “A7” of the previous

page.

Summary of Contents for Mr.Slim PUHZ-P100VKA
















































































































Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Service Manual

Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands