background image

76

OCH670

SW2 setting

Display detail

Explanation for display

Unit

:

Indoor pipe temperature / Liquid (TH2) 

on error occurring

- 39 to 88

- 39 to 88

(When the temperature is 0 °C or less, “–” and 

 temperature are displayed by turns.)

(Example) When -15 °C;

                                     0.5 s       0.5 s        2 s

Indoor pipe temperature / Cond./ Eva. 

(TH5) on error occurring

- 39 to 88

- 39 to 88

(When the temperature is 0 °C or less, “–” and 

 temperature are displayed by turns.)

(Example) When -15 °C;

                                     0.5 s       0.5 s        2 s

Outdoor 2-phase pipe (TH6) on error 

occurring

- 39 to 88

- 39 to 88

(When the temperature is 0 °C or less, “–” and 

 temperature are displayed by turns.)

(Example) When -15 °C;

                                      0.5 s       0.5 s        2 s

Outdoor ambient temperature (TH7) on 

error occurring

- 39 to 88

- 39 to 88

(When the temperature is 0 °C or less, “–” and 

 temperature are displayed by turns.)

(Example) When -15 °C;

                                     0.5 s        0.5 s        2 s

Outdoor heatsink temperature (TH8) on 

error occurring

- 40 to 200

- 40 to 200

(When the temperature is 0°C or less, “–” and 

 temperature are displayed by turns.)

(When the temperature is 100°C or more, hundreds

 digit, tens digit and ones digit are displayed by

 turns.)

1

ON

2 3 4 5 6

1

ON

2 3 4 5 6

1

ON

2 3 4 5 6

1

ON

2 3 4 5 6

1

ON

2 3 4 5 6

15

15

15

15

:

:

:

The black square ( ) indicates a switch position.

1

ON

2 3 4 5 6

:

0 to 255

(When the temperature is 100 °C or more, hundreds

 digit, tens digit and ones digit are displayed by 

 turns.)

(Example) When 150 °C;

                                   0.5 s        0.5 s         2 s

1

ON

2 3 4 5 6

Discharge superheat on error occurring

SHd

0 to 255

   SHd = TH4 - TH6

   

50

1

Thermo-on time until error stops

0 to 999

0 to 999

(When it is 100 minutes or more, hundreds digit, tens

 digit and ones digit are displayed by turns.)

(Example) When 415 minutes; 

                                     0.5 s       0.5 s        2 s

1

ON

2 3 4 5 6

Minute

15

4

:

Summary of Contents for Mr.Slim PUHZ-P100VKA
















































































































Reviews: