Mitsubishi Electric Mr.Slim PUHZ-P100VKA Service Manual Download Page 108

Page: 108 / 111

108

OCH670

10. Removing the high pressure switch (63H)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove 2 front cover panel fixing screws (5 × 12) and

remove the front cover panel. (See Photo 1)

(4) Remove 4 back cover panel fixing screws (5 × 12) and

remove the back cover panel. (See Photo 4)

(5) Remove 4 right side panel fixing screws (5 × 12) in the rear of

the unit and remove the right side panel (See Photo 18)

(6) Pull out the lead wire of high pressure switch. (See Photo 18)

(7) Recover refrigerant.

(8) Remove the welded part of high pressure switch.

Note 1: Recover refrigerant without spreading it in the air.

Note 2: The welded part can be removed easily by

removing the right side panel.

Note 3: When installing the high pressure switch, cover it

with a wet cloth to prevent it from heating (100°C

or more), then braze the pipes so that the inside of

pipes are not oxidized.

8. Removing LEV coil

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the LEV coil by sliding the coil upward.

(See Photo 19)

(4) Disconnect the connectors, LEV-B (RD) on the controller

circuit board in the electrical parts box.

9. Removing LEV

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove 2 front cover panel fixing screws (5 × 12) and

remove the front cover panel. (See Photo 1)

(4) Remove 4 back cover panel fixing screws (5 × 12) and

remove the back cover panel. (See Photo 4)

(5) Remove 3 valve bed fixing screws (4 × 10) and 4 stop

valve fixing screws (5 × 16, 2 for gas and 2 for liquid) then

remove the valve bed.(See Photo 18)

(6) Remove 2 right side panel fixing screws (5 × 12) in the rear

of the unit then remove the right side panel.

(See Photo 18)

(7) Remove the LEV coil.(See Photo 19)

(8) Recover refrigerant.

(9) Remove the welded part of LEV.

Note 1: Recover refrigerant without spreading it in the air.

Note 2: The welded part can be removed easily by

removing the right side panel.

Note 3: When installing the LEV, cover it with a wet cloth

to prevent it from heating (120°C or more), then

braze the pipes so that the inside of pipes are not

oxidized.

Photo 19

LEV coil

Stop valve

Valve bed

fixing screws

Valve bed

fixing screw

Side panel

fixing screw

Photo 18

(Fixing the

right side

panel also)

Side panel

4-way

valve coil

4-way valve

4-way valve coil

fixing screw

High pressure switch

OPERATING PROCEDURE

PHOTOS/FIGURES

Summary of Contents for Mr.Slim PUHZ-P100VKA
















































































































Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Service Manual

Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands