Mitsubishi Electric Mr.Slim PUHZ-P100VKA Service Manual Download Page 23

Page: 23 / 111

OCH670

Error information

Error code

Error unit IU

Ref. address Unt#

Model name

Serial No.

Reset

Page

Error information

Contact information

Dealer

Tel

Reset

Page

Reset error: Reset button

blinks

Check code, error unit, refrigerant address, unit model name, and serial

number will appear.

The model name and serial number will appear only if the information have

been registered.

Press the F1 or F2 button to go to the next page.

When an error occurs, the following screen will appear.

Check the error status, stop the operation, and consult your dealer.

Contact information (dealer's phone number) will appear if the information have

been registered.

Error information

Error reset

Error code

Error unit IU

Ref. address Unt#

Model name

Serial No.

Reset

Page

Reset current error?

Error reset

Cancel

Main menu:

Reset error: Reset button

blinks

Press the F4 button or the

button to reset the error that is occurring.

Errors cannot be reset while the ON/OFF operation is prohibited.

Select "OK" with the F4 button.

Navigating through the screens

• To go back to the Main menu ..........

button

<Error information>

Summary of Contents for Mr.Slim PUHZ-P100VKA
















































































































Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Service Manual

Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands