Mitsubishi Electric Mr.Slim PUHZ-P100VKA Service Manual Download Page 40

Page: 40 / 111

OCH670

Check code

Abnormal points and detection method

Judgment and action

Case

(6840)

Indoor/outdoor unit communication

error (Signal receiving error)

(Outdoor unit)

Abnormal if outdoor controller circuit board

could not receive anything normally for 3

minutes.

Contact failure of indoor/

outdoor unit connecting wire

Defective communication circuit

of outdoor controller circuit board

Defective communication circuit

of indoor controller board

Noise has entered into indoor/

outdoor unit connecting wire.

Check disconnection or looseness of indoor/

outdoor unit connecting wire of indoor or

outdoor units.

–

Turn the power off, and on again to

check. Replace indoor controller board

or outdoor controller circuit board if

abnormality is displayed again.

Remote controller transmission error

(E3)/signal receiving error (E5)

Abnormal if remote controller could not

find blank of transmission path for 6

seconds and could not transmit.

(Check code: E3)

Remote controller receives transmitted

data at the same time, compares the

data, and when detecting it, judges

different data to be abnormal 30

continuous times. (Check code: E3)

Abnormal if indoor controller board could

not find blank of transmission path.

(Check code: E5)

Indoor controller board receives

transmitted data at the same time,

compares the data, and when detecting

it, judges different data to be abnormal

30 continuous times. (Check code: E5)

Set a remote controller to main, and the

other to sub.

Remote controller is connected with only one

indoor unit.

The address changes to a separate setting.

–

Diagnose remote controller.

a) When “RC OK” is displayed, remote

controllers have no problem.

Turn the power off, and on again to check.

When becoming abnormal again, replace

indoor controller board.

b) When “RC NG” is displayed, replace

remote controller.

c) When “RC E3” or “ERC 00-66” is

displayed, noise may be causing

abnormality.

2 remote controller are set as

“main.”

(In case of 2 remote controllers)

Remote controller is connected

with 2 indoor units or more.

Repetition of refrigerant

address

Defective transmitting receiving

circuit of remote controller

Defective transmitting receiving

circuit of indoor controller board

Noise has entered into

transmission wire of remote

controller.

(6840)

Indoor/outdoor unit communication

error (Signal receiving error)

Abnormal if indoor controller board could

not receive any signal normally for 6

minutes after turning the power on.

Abnormal if indoor controller board could

not receive any signal normally for 3

minutes.

Consider the unit as abnormal under

the following condition. When 2 or more

indoor units are connected to an outdoor

unit, indoor controller board could not

receive a signal for 3 minutes from

outdoor controller circuit board, a signal

which allows outdoor controller circuit

board to transmit signals.

Check LED display on outdoor controller circuit

board. (Connect A-Control service tool (PAC-

SK52ST))

Refer to EA~EC item if LED displays EA~AC.

Check disconnecting or looseness of indoor

/outdoor unit connecting wire of indoor unit

or outdoor unit.

Check all the units in case of twin/triple/

quadruple indoor unit system.

–

Turn the power off, and on again to check.

If abnormality generates again, replace indoor

controller board or outdoor controller circuit

board.

* Other indoor controller board may have

defect in case of twin/triple/quadruple indoor

unit system.

Turn the power off, and detach fan motor

from connector (CNF1, 2). Then turn the

power on again.

If abnormality is not displayed, replace fan

motor.

If abnormality is displayed, replace outdoor

controller circuit board.

Connect 52C relay properly to CN52C

(PUHZ-P·VKA)

Contact failure, short circuit or

miswiring (converse wiring) of

indoor/outdoor unit connecting

wire

Defective transmitting receiving

circuit of outdoor controller

circuit board.

Defective transmitting receiving

circuit of indoor controller

board.

Noise has entered into indoor/

outdoor unit connecting wire.

Defective fan motor

Disconnection of 52C relay

(PUHZ-P·VKA)

Indoor/outdoor unit communication

error (Transmitting error)

Abnormal if “1” receiving is detected 30

times continuously though indoor controller

board has transmitted “0”.

Defective transmitting receiving

circuit of indoor controller board

Noise has entered into power

supply.

Noise has entered into outdoor

control wire.

–

Turn the power off, and on again to

check. If abnormality generates again,

replace indoor controller board.

Summary of Contents for Mr.Slim PUHZ-P100VKA
















































































































Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Service Manual

Search results

Summary of Contents for Mr.Slim PUHZ-P100VKA

Reviews:

Related manuals for Mr.Slim PUHZ-P100VKA

Brands by name

Popular brands