Mitsubishi Electric ME96 Series Manual Download Page 5

Page: 5 / 40

*1 : ME-0040MT2-SS96 is only applicable to ME96SSHB-MB with firmware

version 01.01 or later.

CC-Link System (With optional plug-in module (ME-0040C-SS96))

MODBUS TCP System (With optional plug-in module (ME-0000MT-SS96/ME-0040MT2-SS96 *

))

Data Logging (Built-in logging function and optional plug-in module (ME-0000BU-SS96))

Analog/Pulse/Alarm Output System (With optional plug-in module (ME-4210-SS96B))

Applicable to analog output, pulse output and alarm output with the aid of the optional module
ME-4210-SS96B.

Remote monitoring of A, DA, V, W, var, VA, PF, Hz, Harmonics Current RMS value and
Harmonics voltage RMS value at 4 mA to 20 mA output (max. 4 outputs).

Active energy, reactive energy, apparent power and periodic energy can be monitored by
pulse output (max. 2 pulses).

Can remotely monitor upper/lower limit alarm by digital output (max. 2 points).

This is a MODBUS TCP communication unit that can be used in the Ethernet system. The number of

network system selection methods is increased, and Ethernet and MODBUS RTU communication can
be duplicated.

The optional plug-in module ME-0040MT2-SS96 has 2 Ethernet ports, so straight-line topology is

possible without using Ethernet SWITCH/HUB.

The optional plug-in module ME-0040MT2-SS96 has 4 digital inputs, so remote monitoring of status

signals is possible without a PLC.

Digital input signal can be latched for over 30

ms,

and there is no need for external latch circuits.

The ME96SSHB-MB/ME96SSRB-MB has a built-in logging function stores measurement data as logging data in the internal non-volatile
memory. The data to be stored as events occurred in this instrument are alarm data, the recorded time of the Max/Min value, and system log
data. The stored data can be read from MODBUS RTU communication.

Optional module ME-0000BU-SS96 can memorize the data of various quantities related to electricity measured by ME96SS-Ver.B for a certain
period. Therefore, measurement data can be backup even when the MODBUS RTU communication of ME96SS-Ver.B fails.
Memorized measurement data can be output to an SD memory card in CSV format. You can check the data files output to the SD memory
card by Microsoft Excel.

• 4 mA to 20 mA

• 4 outputs

• Resistance load 600

or less

• No-voltage a contact point

• 35 V DC, 0.1 A

• Select output from pulse widths of 0.125 s, 0.5 s or 1 s

• Ethernet port : 10BASE-T/100BASE-TX

• Maximum segment length : 100 m
<Optional Plug-in Module ME-0000MT-SS96>

• Number of ports : 1

• Digital Input : non
<Optional Plug-in Module ME-0040MT2-SS96 *

• Number of ports : 2

• Digital Input : 4 points (24 V DC)

• No-voltage a contact point

• 35 V DC, 0.1 A

• 1 point (24 V DC)

Outline and Features

ME96 Super-S Series Ver.B Features

ME96SSHB-MB

(High-performance model)

ME96SSRB-MB

(Standard model)

ME96SSEB-MB

(Economy model)

MODBUS RTU communication
Plug-in module (options)

• Analog/Pulse/Digital output/input

• CC-Link communication

• Digital input/output (for MODBUS RTU communication)

• Backup (on SD card)

• MODBUS TCP communication

MODBUS RTU communication
Plug-in module (options)

• Analog/Pulse/Digital output/input

• CC-Link communication

• Digital input/output (for MODBUS RTU communication)

• Backup (on SD card)

• MODBUS TCP communication

MODBUS RTU communication

A, DA, V, Hz = ±0.1%

W, var, VA, PF = ±0.2%

VAh = ±2.0%

Wh = class 0.5S (IEC62053-22)

varh = class 1S (IEC62053-24)

Harmonics = 31

-deg (max)

Rolling demand = W, var, VA

A, DA, V = ±0.2%

Hz = ±0.1%

W, var, VA, PF = ±0.5%

VAh = ±2.0%

Wh = class 0.5S (IEC62053-22)

varh = class 1S (IEC62053-24)

Harmonics = 19

-deg (max)

Rolling demand = W, var, VA
A, DA, V = ±0.5%

Hz = ±0.2%

W, var, VA, PF = ±0.5%

VAh = ±2.0%

Wh = class 0.5S (IEC62053-22)

varh = class 1S (IEC62053-24)

Harmonics = Only total

Optional Plug-in Modules

Note 1: Optional Plug-in Module can not be used with ME96SSEB-MB.
Note 2: For details of each characteristic, refer to the specifications section.

*1: 2 ports for daisy chain, one IP address.
*2: Applicable only to firmware version 01.01 or later.

Optimum transmission system for remote monitoring using Mitsubishi PLC.

Contact signals can be remotely monitored by installing the optional module ME-0040C-SS96. This is
helpful in wiring and space saving.

Digital input signals can be latched for over 30 ms, and there is no need for external latch circuits.

Abnormal Signal (Facility)
Abnormal Signal (Earth Leakage)
Abnormal Signal (Temperature)
Circuit Breaker Status Signal, etc.

<CC-Link Interface>

• Max. Baud rate: 10 Mbps

• Max. Connection Distance: 100 m (10 Mbps)-

1,200 m (156 kbps)

• Max. Connection Units: 42

• Digital Input: 4 points (24 V DC)

CC-Link

Ethernet

MELSEC Series

MODBUS RTU System

Central monitor

RS485/USB

converter

RS485 (MODBUS RTU)

USB

MODBUS RTU communication system optimizes computer monitoring operations.

In addition, when ME-0052-SS96 is installed, remote monitoring of digital input signals and on/off
control of digital output signals are possible. Therefore, no other DI/DO terminals are required.

Digital input signals can be latched for over 30 ms, and there is no need for external latch circuits.

ME-0052-SS96

optional unit

Tripping
Closing
AL
PAL
TAL
Turning on/off breaker, etc.

• Max. Baud rate: 38.4 kbps
• Max. Connection Distance: 1,200 m
• Max. Connection Units: 31

• Digital Input: 5 points (24 V DC)
• Digital Output: 2 points (35 V DC)

Model name

Transmission/Option specifications

Main measurement items

Added measurement function, reactive energy, apparent energy, reactive power and apparent power for ME96SSEB-MB.

Realized downsizing for ME96SSEB-MB.

Improved Measurement Functions