Mitsubishi Electric ME96 Series, Manual

Page: 23 / 40

Operating Instructions
Set-up menu
DISPLAY SET
DISPLAY SET
DISPLAY SET Set-up menu 6: Analog output setting (only when ME-4210-SS96B is installed)
* Only for ME96SSHB-MB or ME96SSRB-MB, it is applicable.
non
A
1
A
2
A
3
A
N
A
AVG
(CH1)
Demand A
1
Demand A
2
Demand A
3
Demand A
N
Demand A
AVG
V
1N
V
2N
V
3N
V
AVG
(L-N) (CH2)
V
12
V
23
V
31
V
AVG
(L-L)
W
1
W
2
W
3
W
Σ
(CH3)
var
1
var
2
var
3
var
Σ
VA
1
VA
2
VA
3
VA
Σ
PF
1
PF
2
PF
3
PF
Σ
(CH4)
Hz
Harmonic A
1
Harmonic A
2
Harmonic A
3
Harmonic A
N
Harmonic V
1N
Harmonic V
2N
Harmonic V
3N
3-phase 4-wire
AVG: Average value, Σ : Total RMS value
DISPLAY SET
DISPLAY SET
To next channel settings
w
Analog output CH1
output item
DISPLAY SET
q
Optional selection
e
Analog output CH1
detailed settings
20
4
12
mA
1
−
0.5
20
4
12
mA
1
−
0 0
0
20
4
mA
40 kW
20
4
12
mA
0
−
40 kW 40 kW
Adjust the set-up menu No. to “6”.
Select “Analog output” or “Built-in logging”.
The explanation here is about analog output setting.
When 3-phase 4-wire system has been selected
w
Set the output item for “analog output CH1”.
Select the measured item to be output from the table below.
e
Set the details for “analog output CH1.”
(The following settings can be made separately from the measurement items included in the display pattern.)
(1) If analog output is selected for current, current demand, voltage,
power, reactive power, power factor (set-up menu: 6.6.1)
(2) If analog output is selected for current, current demand, power
(set-up menu: 6.6.2)
Notes 1. The same measurement items can be set for all channels.
Notes 2. Measurement items not included in the selected display pattern can also be chosen.
Notes 3. Channels set to “non” will have minimum output (4 mA). Additionally, set-up will proceed to the
next channel.
Notes 4. Underlined specifications are factory default settings of measurement items allocated to each
channel.
Notes 5. Harmonic current is output at the scale of 0-60% (with respect to rated value) of the total
effective value. Harmonic voltage is output at the scale of 0-20% of the total distortion ratio.
w
q
e (1)
e (2)
CT primary current value (value set for set-up menu 1.4.1 primary current setting )
A
Demand A
V
W
var
PF
SP. (special primary current value)
Output item Setting range
−0.5-1-0.5 −0-1-0
+10 steps (approx. 250%)
±0 steps (100%: Standard value)
−18 steps (approx. 20%)
+3 steps (approx. 120%)
±0 steps (100%: Standard value)
−18 steps (approx. 20%)
A
Demand A
W
Output item Setting range
Positive-only Positive/Negative
+3 steps (approx. 120%)
±0 steps (100%: instrument rating)
−10 steps (approx. 40%)
<Positive-only> <Positive/Negative>
0.5
SET
e
Use this to set the cycle in which detailed data of the built-in logging item pattern “LP01” or “LP02” are logged.
15 min 30 min 60 min
Set-up menu According to “3.1 Set-up Flow”, either exit from setting or continue setting in any other set-up menu.
DISPLAY SET
Set-up menu
y Analog output limit
The setting procedure is the same as that of q Analog output CH1 output item .
r
Set the output item for “analog output CH2-4.”
The setting procedure is the same as that of w Analog output CH1 detailed settings .
t
Set the details for “analog output CH2-4.”
y Set the upper limit for analog output (same for all channels).
Select another set-up menu or end set-up.
DISPLAY SET
r
Analog output CH2-4
output item
t
Analog output CH2-4
detailed settings
y
SET
oFF
(no limit)
on
(limit)
Setting Explanation
Output to +5% of upper limit and -5% of
lower limit (with respect to span value)
Output to +1% of upper limit and -1% of
lower limit (with respect to span value)
Note: Skip this setting when the analog output of all channel output items is set to “non.”
‡
To continue to set-up
Select the menu
No. using the or button.
‡
To finish set-up
Press the or button
to display the End screen,
then press the button
to save settings.
SET
t
Built-in logging
period
buiLt
(Built-in logging)
Ao
(Analog output)
<Continued from previous page>
21 22