Mitsubishi Electric ME96 Series, Manual

Page: 15 / 40

Specifications Operating Instructions
‡
Functions
» LCD Functions
‡
Set-up
» Set-up workflow (Example for ME96SSHB-MB)
» Button Functions
For correct measurement, it is necessary to set the primary voltage/current in the set-up mode.
Enter the setting mode from the operating mode and set the necessary items. Any items not set remain in the factory default.
Set-up menu End
Display
pattern
Phase wire
system
VT/direct
voltage
CT current
Frequency
Rolling demand
time limit
Curent demand
time limit
Set-up menu 1
MODBUS RTU
address
Communication
setting selection
MODBUS RTU
baud rate
MODBUS RTU
parity
MODBUS RTU
stop bit
Set-up menu 2
Active/Reactive
energy measurement
method
Harmonic
display
Unbalance
rate display
Set-up menu 3
Model
display
Version
display
Backlight
brightness
Backlight On/
auto Off
Display
update time
Analog
output 1
Analog
output 2
Analog
output 3
Analog
output 4
Output
limit
CC-Link
station No
CC-Link
baud rate
CC-Link version
setting
CC-Link
reset
Set-up menu 4
Upper/lower
limit alarm
element
Upper/lower
limit alarm
value
Alarm delay
time
Alarm reset
method
Motor starting
current delay
time
Backlight
blinking at
alarm
Pulse/alarm
output function
Pulse output
Set-up menu 5 Set-up menu 6
Periodic
active energy
display
Periodic active
energy changeover
setting
Rolling
demand
display
Rolling demand
time limit adj.
setting
Digital I/O
display
Digital input
reset method
Set-up menu 7
Operating time
display
Test mode
Operating time
count target
Operating time
threshold value
IEC mode
setting
CO
2
equivalent
display
CO
2
conversion
rate
Set-up menu 8 Setting value confirmation menu 9
End display
Cancel
display
<When ME-0040C-SS96 is installed>
<When ME-0000MT-SS96 or ME-0040MT2-SS96 is installed>
Optional
selection
Built-in
logging data
Clear
Built-in
logging
Use/nonuse
Built-in logging
item pattern
Built-in
logging period
interval
Logging ID
Logging data
Clear
Logging
item pattern
Detail data
logging period
interval
<When ME-4210-SS96B is installed>
<When ME-4210-SS96B, ME-0052-SS96,
ME-0040C-SS96 or ME-0040MT2-SS96 is installed>
<When ME-4210-SS96B is installed>
<When ME-0000BU-SS96 is installed>
MODBUS TCP
IP address
MODBUS TCP
subnet mask
MODBUS TCP
use/nonuse of
default gateway
MODBUS TCP
default gateway
MODBUS TCP
reset
1 2 3
4
6
13
12 11 10 9 8 7
5
Functions Button operation Functions
Basic performance
Button operation
Used to set items such as primary voltage and
current, and to choose setting items
Push for
2 seconds
Push for
2 seconds
Push for
2 seconds
Push for
2 seconds
Push for
1 seconds
Used to reset Wh, varh, and VAh to zero by
concurrently pushing for 2 seconds
Used to perform fast-forward or fast-return of
numerical values in numerical value setting
Used to perform batch reset of all the
max/min values
Used to change Wh, etc. to another unit and
to low order zoom display
Used to switch display between setting
Used to switch display between max/min values and
instantaneous value
Used to change over phase
Used to change over the display screen
Used to switch display between manual
phase change
⇔
cyclic phase change
Used to switch display between manual
display change
⇔
cyclic display change
or
MAX/MIN
PHASE
DISPLAY
DISPLAY
PHASE
RESET
SET RESET PHASE
+
or
+ +
+
SET
Special performance
Note. An example. For details, refer to the user’s manual.
Change/
Confirm
values set
Enter
set-up
mode
Enter setting value
confirmation mode
Measurement screen
Notes 1. Basic measurements are possible by adjusting settings in the menu 1
( area enclosed by dotted line).
Notes 2. Item settings vary depending on the model.
Notes 3. Setting confirmation menu 9 (test mode) is not displayed in the setting mode.
Operation (function) details
Access set-up mode from operating mode
Access setting value confirmation
mode from operating mode
Save settings and return to operating mode
Select set-up menu
Move to next screen
Return to previous setting item
Skip remaining settings
Select cancel
Button operation
Simultaneously press for 2 s
Press for 2 s
Press for 1 s
Symbol
+
or
or
DISPLAY
SET
SET
RESET
SET
SET
SET
No. Name of each part Function
1 LEAD status Light up when leading reactive energy is measured
2 LAG status Light up when lagging reactive energy is measured
3 Built-in logging status Light up when the built-in logging function is operating
4 Digital element display Display measuring elements expressed in digital numbers
5 Digital display Display measured values in digital numbers
6 Unit Display the units of measured values
7 Setup status
Light up in the setting mode
Blink in the setting confirmation mode
8 Test mode status Light up in the test mode
9 Clock status Light up when the date and time are set
10 Upper/lower limit alarm status Blink when the upper/lower limit alarm is generating
11
Communication/
Option logging status
Specification ON Blink OFF
CC-Link
communication
Normal
CC-Link version mismatches,
Hardware abnormality Hardware
abnormality
MODBUS RTU communication
MODBUS TCP communication
Normal
Communication error such as
wrong address
*1
Hardware
abnormality
Logging function Normal
Error occurrence such as
setting abnormality, SD
memory card error, or battery
voltage drop
*1
Hardware
abnormality
*1. For details, refer to User’s Manual.
12 Harmonics status Light up when harmonic is displayed
13 Metering status
Blink when Imported active energy is measured
*Note 1
*It appears on the imported active energy display screen only
Note 1. The blinking cycle is constant regardless of measuring input size.
13 14