Mitsubishi Electric FR-A700-A1, Instruction Manual

Page: 12 / 86

9
PARAMETER LIST
2
P
A
RA
M
E
T
E
R L
IST
547
Parameter for manufacturer setting. Do not set.
548
549
Protocol selection 0, 1 1 0 —
550
NET mode operation command source
selection
0, 1, 9999 1 9999 —
551
PU mode operation command source
selection
1, 2, 3 1 2 —
555 Current average time 0.1 to 1s 0.1s 1s —
556 Data output mask time 0 to 20s 0.1s 0s —
557
Current average value monitor signal
output reference current
0 to 500/0 to 3600A
*2
0.01/0.1A
*2
Rated
inverter
current
—
563 Energization time carrying-over times (0 to 65535) 1 0 —
564 Operating time carrying-over times (0 to 65535) 1 0 —
569 Second motor speed control gain 0 to 200%, 9999 0.1% 9999 —
571 Holding time at a start 0 to 10s, 9999 0.1s 9999 —
574 Second motor online auto tuning 0, 1 1 0 —
575 Output interruption detection time 0 to 3600s, 9999 0.1s 9999 —
576 Output interruption detection level 0 to 400Hz 0.01Hz 0Hz —
577 Output interruption cancel level 900 to 1100% 0.1% 1000% —
611 Acceleration time at a restart 0 to 3600s, 9999 0.1s 5/15s
*2
—
665
Regeneration avoidance frequency
gain
0 to 200% 0.1% 100% —
684 Tuning data unit switchover 0, 1 1 0 —
702 Dancer position detection level 0 to 100% 0.01% 10% 27
703 Minimum number of input pulse 0 to 100kpps 0.01kpps 0kpps 45
704 Maximum number of input pulse 0 to 100kpps 0.01kpps 100kpps 45
706 Speed compensation gain 0 to 200% 0.1% 0% 31
707
Sampling time for winding diameter
calculation
0.01 to 1s, 9999 0.01s 9999 38
708
Filter time constant for dancer control
input
0 to 5s 0.001s 0s 27
709 Integral clamp (positive polarity) 0 to 100%, 9999 0.1% 9999 26
710 Integral clamp (negative polarity) 0 to 100%, 9999 0.1% 9999 26
711 Signal loss detection stationary time 0 to 100s, 9999 0.01s 9999 28
712
Initial winding diameter calculation
dead zone 2
0 to 50%, 9999 0.1% 9999 40
713 Initial inertia moment
0 to 500kg · m
2
0.01kg · m
2
0kg · m
2
62
714 Roll width 0 to 5000mm 1mm 0mm 62
715 Material specific gravity
0 to 20g/cm
3
0.001g/cm
3
0g/cm
3
62
716 Inertia compensation cushion time 0 to 360s 0.01s 0s 62
717 Tension command cushion time 0 to 360s 0.01s 0s 61
718 Dancer tension setting bias 0 to 200% 0.1% 0% 51
719 Dancer tension setting gain 0 to 200% 0.1% 100% 51
720 Maximum winding diameter 1 1 to 6553mm 1mm 2mm 35
721 Minimum winding diameter 1 1 to 6553mm 1mm 1mm 35
722 Maximum winding diameter 2 1 to 6553mm 1mm 2mm 35
723 Minimum winding diameter 2 1 to 6553mm 1mm 1mm 35
724 Maximum winding diameter 3 1 to 6553mm 1mm 2mm 35
725 Minimum winding diameter 3 1 to 6553mm 1mm 1mm
35
726 Maximum winding diameter 4 1 to 6553mm 1mm 2mm 35
727 Minimum winding diameter 4 1 to 6553mm 1mm 1mm 35
728 Main speed analog gain 2 0 to 400Hz, 9999 0.01Hz 9999 44
729 Main speed analog gain 3 0 to 400Hz, 9999 0.01Hz 9999 44
730 Main speed analog gain 4 0 to 400Hz, 9999 0.01Hz 9999 44
731 Dancer signal input selection 3 to 6 1 5 27
732
Dancer main speed command input
selection
0 to 7 1 0 43
Parameter Name Setting Range
Minimum
Setting
Increments
Initial
Value
Refer
to
Page
Customer
Setting