Mitsubishi Electric 9800A Series Owner Technical Manual Download Page 8

Page: 8 / 72

MITSUBISHI ELECTRIC 9800A SERIES UPS

MITSUBISHI
ELECTRIC

9800A SERIES UPS

OWNERS / TECHNICAL MANUAL

Page Number:

1-2

In no event will MITSUBISHI be responsible or liable for either indirect or

consequential damage or injury that may come from the use of this equipment.

Any modifications without authorization by MITSUBISHI could result in personal injuries,

death or destruction of the UPS.

1.1

SAFETY PRECAUTIONS

APPLICATION

This UPS shall NOT be applied to support equipment (*) that could affect

the human lives.

Special considerations are required when applying this UPS to the

equipment (**) that affect human safety and/or maintain public services.

Be sure to contact/inform MITSUBISHI if it is such a case. The application

without special consideration may cause serious accidents.



Medical operation room equipment



Life support equipment (artificial dialysis, incubators, etc.)



Toxic gas or smoke eliminators



Equipment that must be provided under fire laws, construction standards
or other ordinances



Equipment equivalent to the above



Equipment to supervise or control airways, railways, roads, sea-lanes
or other transportation.



Equipment in nuclear power plants.



Equipment to control communications.



Equipment equivalent/similar to the above mentioned.

WARNING

Summary of Contents for 9800A Series









































































Search results

Summary of Contents for 9800A Series

Reviews:

Related manuals for 9800A Series

Brands by name

Popular brands

Mitsubishi Electric 9800A Series, Owner Technical Manual

Search results

Summary of Contents for 9800A Series

Reviews:

Related manuals for 9800A Series

Brands by name

Popular brands