Mitsubishi Electric 9800A Series Owner Technical Manual Download Page 25

Page: 25 / 72

MITSUBISHI ELECTRIC 9800A SERIES UPS

MITSUBISHI
ELECTRIC

9800A SERIES UPS

OWNERS / TECHNICAL MANUAL

Page Number:

2-2

2.1 LED DISPLAY

Load on inverter [ LOAD ON INVERTER ](green)

Illuminates when power is supplied from inverter to the critical load.

(Indicates the state of inverter transfer switch "52C".)

Battery operation [ BATTERY OP. ](orange)

Illuminates when power is supplied from batteries following a power failure.

Load on bypass [ LOAD ON BYPASS ](orange)

Illuminates when power is supplied to load devices by static bypass.

(Indicates the state of bypass transfer switch "52S".)

Overload [ OVERLOAD ](orange)

Illuminates in overload condition.

LCD fault [ LCD FAULT ](red)

Illuminates when an error occurs.

UPS fault [ UPS FAULT ](red)

[Annunciator: intermittent or constant tones]

Illuminates when an error occurs in the system. In this case, the details of the error are

indicated on the display panel.

2.2 EPO BUTTON (Emergency Power Off button) (7)

When activated, the Emergency Power Off (EPO) function shuts down the UPS module.

The critical load will lose power and also shutdown. The EPO function can be performed

both locally or remotely.

Summary of Contents for 9800A Series









































































Search results

Summary of Contents for 9800A Series

Reviews:

Related manuals for 9800A Series

Brands by name

Popular brands

Mitsubishi Electric 9800A Series, Owner Technical Manual

Search results

Summary of Contents for 9800A Series

Reviews:

Related manuals for 9800A Series

Brands by name

Popular brands