Mitel DBC 223 Directions For Use Manual Download Page 83

Page: 83 / 121

OICE

4223 O

FFICE

(DBC 223)

FOR

OICE

MX-ONE

3/1553-ANF 901 54 Uen F5 2018-12-03

•

Replace the handset.

8.2.5

TO REVERT TO THE INTERNAL GROUP HUNTING GROUP

•

Lift the handset (dial tone).

•

Dial #24*the group number# (dial tone).

•

Replace the handset.

8.3

GROUP DO NOT DISTURB

The group do not disturb feature allows a user (with a directory number defined as

master extension by a command) to mark a group of extensions as group do not

disturb, that is, calls to extensions in the group are not indicated.
An extension with group do not disturb activated can still make outgoing calls in the

normal way.
The master extension category can be assigned either to a triple access line or to an

additional line.

8.3.1

TO ORDER GROUP DO NOT DISTURB

An extension defined as master extension can activate group do not disturb by dialing

the following procedure:
•

Lift the handset (dial tone).

•

Dial *25*group number# (special dial tone).

•

Replace the handset.

8.3.2

TO CANCEL GROUP DO NOT DISTURB

An extension defined as master extension can cancel group do not disturb by dialing

the following procedure:
•

Lift the handset (dial tone).

•

Dial #25*group number#.

•

Replace the handset.

8.3.3

BYPASS OF GROUP DO NOT DISTURB

An extension defined as master extension can bypass the group do not disturb feature

by dialing the following procedure:
•

Lift the handset (dial tone).

•

Dial *60*extension number#.

The call is indicated on the dialed extension number.

Summary of Contents for DBC 223


























































































































Search results

Summary of Contents for DBC 223

Reviews:

Mitel DBC 223, Directions For Use Manual, Page: 83 / 121

Search results

Summary of Contents for DBC 223

Reviews: