Mitel DBC 223 Directions For Use Manual Download Page 16

Page: 16 / 121

3/1553-ANF 901 54 Uen F5 2018-12-03

ELEPHONE

INSTRUMENT

DBC 223

state) allows the cancellation of the service. Depending on the active services this

soft-key is called

NoDiversion

Cancel DND

All the services offered by this soft-key

Absence

are:

•

Select Profile

•

Direct Diversion to nnnn*

•

Follow Me

•

Absence reason

•

External Follow Me

•

Do not Disturb

•

Diversion on no answer to nnnn*

•

Diversion on busy to nnnn*

*nnnn

Current number is shown

The display with the absence services has the following appearance:

Figure 3: Display, soft-keys from idle state.
xxx

: soft-key not relevant for this example.

Once the soft-key

Absence

is selected:

Figure 4: Display, after selecting Absence. Directory number 3000 is just an

example.

If a service is available it is displayed in a 100% grey scale. Otherwise, the option will

be displayed in a softer grey scale (30%).
After pressing the soft-key

Down

three times:

Summary of Contents for DBC 223


























































































































Search results

Summary of Contents for DBC 223

Reviews:

Mitel DBC 223, Directions For Use Manual, Page: 16 / 121

Search results

Summary of Contents for DBC 223

Reviews: