manualshive.com logo in svg

Mitel DBC 223, Directions For Use Manual, Page: 65 / 121

Share
Download
Mitel DBC 223 Directions For Use Manual Download Page 65

M

I

V

OICE

 4223 O

FFICE

 (DBC 223) 

FOR

 M

I

V

OICE

 MX-ONE

65

3/1553-ANF 901 54 Uen F5 2018-12-03

6  

CALL FORWARDING

6.1 

DIVERSION

6.1.1 

DIRECT DIVERSION

If you are unable to accept calls, you can have them directly diverted to an individual 

or, if no such position exists, three predetermined common answering positions.
Depending on type of calling party (internal, private net or external party) the calls are 

diverted to either the individual or common answering position. This is set by the 

system administrator.
When your telephone is diverted you can still make calls from it as usual.
As a reminder that your telephone is diverted you will hear a special dial tone each time 

you lift the handset to make a call and the Diversion lamp indicates that your triple 

access line is diverted.

6.1.1.1 

To order from your own telephone

Using the soft-key Absence

•

Press the soft-key 

 Absence

  in idle state.

•

From the menu select 

Direct Diversion to NNNN

  (NNNN is the diversion 

number).

•

Press 

Activate

  (the diversion lamp turns ON)

Using the diversion-key

•

Press the Diversion-key (the diversion lamp turns ON).

Note:  

If this is done during reception of dial tone the diversion-key has to be pressed 

twice.

Using a procedure

•

Lift the handset (dial tone).

•

Dial *21# (special dial tone and the diversion lamp turns ON).

•

Replace the handset.

Note:  

For an additional line, the diversion lamp is not affected

6.1.1.2 

To cancel from your own telephone

Using the soft-key NoDiversion

•

Press the soft-key 

 NoDiversion

  (the diversion lamp turns OFF).

Using the diversion-key

•

Press the Diversion-key (the diversion lamp turns OFF).

Using a procedure

•

Lift the handset (special dial tone).

•

Dial #21# (dial tone, the diversion lamp turns OFF).

Summary of Contents for DBC 223


























































































































Reviews:

No comments