manualshive.com logo in svg

Mitel DBC 223, Directions For Use Manual, Page: 19 / 121

Share
Download
Mitel DBC 223 Directions For Use Manual Download Page 19

M

I

V

OICE

 4223 O

FFICE

 (DBC 223) 

FOR

 M

I

V

OICE

 MX-ONE

19

3/1553-ANF 901 54 Uen F5 2018-12-03

2.8.4 

LOUDSPEAKING

This function offers you the possibility of speaking in the handset and at the same time 

letting the conversation be heard in the loudspeaker.

2.8.4.1 

To make calls

•

Lift the handset.

•

Press the Speaker-key.

•

Dial the wanted number.

•

Wait for answer.

2.8.4.2 

To change from loudspeaking with handset to handset

•

Press the Speaker-key.

2.8.4.3 

To change from handset to loudspeaking with handset

•

Press the Speaker-key.

2.8.4.4 

To change from loudspeaking with handset to loudspeaking with headset

•

Press the Headset-key.

2.8.4.5 

To change from loudspeaking with headset to loudspeaking with handset

•

Lift the handset.

2.8.4.6 

To clear the call

•

Press the Clear-key.

2.9 

TONES AND RINGING SIGNALS

2.9.1 

TONE CHARACTERISTICS

The different tone signals sent from the exchange to your telephone are as follows:

Summary of Contents for DBC 223


























































































































Reviews:

No comments