manualshive.com logo in svg

Mitel DBC 223, Directions For Use Manual, Page: 111 / 121

Share
Download
Mitel DBC 223 Directions For Use Manual Download Page 111

M

I

V

OICE

 4223 O

FFICE

 (DBC 223) 

FOR

 M

I

V

OICE

 MX-ONE

111

3/1553-ANF 901 54 Uen F5 2018-12-03

•

From the menu select 

Headset Preset

 and press the soft-key 

Select

A tone signal is heard, and the display shows:

Note:  

The soft-keys are only available when firmware revision R3F or later is active 

for the telephone. See Firmware indication to check the firmware revision. For 

earlier version the settings is automatically changed every time the Headset 

Preset menu is entered.

11.10 Firmware indication on page 113
•

Press the soft-key 

Change

  to switch to Headset Preset- 

Off

  replaced by 

On

 .

•

Press the soft-key 

Save&Exit

 , or press 

#

  to finish setting.

The headset key lamp flashes for some seconds. The headset symbol is displayed to 

indicate Headset Preset.

To cancel using the soft-key PhoneSet

 :

•

Press the soft-key 

PhoneSet

•

From the menu select 

Headset Preset

  and press the soft-key 

Select

 .

A tone signal is heard, and the display shows:

Note:  

The soft-keys are only available when firmware revision R3F or later is active 

for the telephone. See Firmware indication to check the firmware revision. For 

earlier version the settings is automatically changed every time the Headset 

Preset menu is entered.

11.10 Firmware indication on page 113
•

Press the soft-key 

Change

 , or press the Line 1 key to switch to Headset Preset 

Off

 replaced by 

On

 .

•

Press the soft-key 

Save&Exit

 , or press 

#

  to finish setting

The loudspeaker key lamp flashes for some seconds, and the headset symbol disap

-

pears from the display.

To activate using the Headset key:

•

Press the Headset key and hold for at least 4 seconds.

A short acknowledgement tone signal is heard, and the headset key lamp flashes for 

some seconds. The headset symbol is displayed to indicate Headset Preset.

Summary of Contents for DBC 223


























































































































Reviews:

No comments