MINOLTA-QMS Magicolor 2300W User Manual Download Page 109

Page: 109 / 150

Duplex Option

103

Attach the support wire for the duplex option to the printer.

Pull the right-side door release
lever, and open the right-side
door.

Pull the tab for the support wire
on the right side of the duplex
option, and then hook the wire
onto the hook of the printer.

Close the right-side door.

Reconnect the interface cable.

Reconnect the power cord, and turn
on the printer.

In compliance with UL
guidelines, “The appliance
inlet is considered to be the
main disconnect device.”

Start up the Status Display, select
Printer Information on the Display
menu, and then check that the duplex option is installed.

Configure your driver for the new duplex option. (Refer to “Device Options
Setting Tab” on page 38.)

Summary of Contents for Magicolor 2300W























































































































































Search results

Summary of Contents for Magicolor 2300W

Reviews:

Related manuals for Magicolor 2300W

Brands by name

Popular brands

MINOLTA-QMS Magicolor 2300W, User Manual

Search results

Summary of Contents for Magicolor 2300W

Reviews:

Related manuals for Magicolor 2300W

Brands by name

Popular brands