MINOLTA-QMS Magicolor 2300W User Manual Download Page 106

Page: 106 / 150

Introduction

100

Introduction

Attention

Use of accessories not manufactured/supported by MINOLTA-QMS is
not supported by your printer and will void your warranty.

This chapter provides information about the following accessories. Contact
your local vendor or www.minolta-qms.com for compatibility and purchase
information.

Check www.minolta-qms.com for availability of additional accessories.

Attention

Installing accessories always requires that the printer be turned off and
unplugged during installation.

Duplex Option

Duplex (2-sided) printing can be done automatically with a duplex option and
enough memory installed. See “Duplexing” on page 23.

Kit Contents

Duplex option

Two thumbscrews

Duplex Option

Automatic duplexing

Summary of Contents for Magicolor 2300W























































































































































Search results

Summary of Contents for Magicolor 2300W

Reviews:

Related manuals for Magicolor 2300W

Brands by name

Popular brands

MINOLTA-QMS Magicolor 2300W, User Manual

Search results

Summary of Contents for Magicolor 2300W

Reviews:

Related manuals for Magicolor 2300W

Brands by name

Popular brands