Mindray Trio Service Manual Download Page 78

Page: 78 / 82

Trio™ Service Manual

0070-10-0591-01

5 - 3

Appendix

System Alarm Prompts

*XX RANGE EXCEEDED

The measured value of XX
parameter has exceeded the
system measurement range

If message does not clear
contact Customer Service.

REAL CLOCK NEEDSET

If the monitor displays 2000-1-
1, this system prompt reminds
the user that the current system
time is inaccurate

Reset the system time. After
setting the time, the user
should cycle power. This will
avoid any time storage
errors.

REAL CLOCK NOT EXIST

The system has no cell battery
or the battery has run down

Install or replace the cell
battery

SYSTEM WD FAILURE

The system has a fatal error or
failure

Restart the system. If message
does not clear contact
Customer Service.

SYSTEM SOFTWARE ERR

SYSTEM CMOS FULL

SYSTEM CMOS ERR

SYSTEM EPGA FAILURE

SYSTEM FAILURE2

SYSTEM FAILURE3

SYSTEM FAILURE4

SYSTEM FAILURE5

SYSTEM FAILURE6

SYSTEM FAILURE7

SYSTEM FAILURE8

SYSTEM FAILURE9

SYSTEM FAILURE10

SYSTEM FAILURE11

SYSTEM FAILURE12

KEYBOARD NOT AVAILABLE

The keypad cannot be used

Check the keys for abnormal
depression. Contact the
manufacturer for repair.

KEYBOARD COMM ERR

The keypad has a failure

Contact the manufacturer for
repair

KEYBOARD ERROR

KEYBOARD FAILURE

KEYBOARD ERR1

KEYBOARD ERR2

5V TOO HIGH

The power supply has a failure

Restart the system. If message
does not clear contact
Customer Service.

5V TOO LOW

POWER ERR3

POWER ERR4

12V TOO HIGH

12V TOO LOW

POWER ERR7

POWER ERR8

3.3V TOO HIGH

3.3V TOO LOW

PROBLEM/MESSAGE

REASON

SOLUTION

XX represents all the parameter modules in the system such as ECG, NIBP, SpO

, IBP module, etc.

Summary of Contents for Trio



















































































Search results

Summary of Contents for Trio

Reviews:

Related manuals for Trio

Brands by name

Popular brands

Mindray Trio, Service Manual

Search results

Summary of Contents for Trio

Reviews:

Related manuals for Trio

Brands by name

Popular brands