Mindray Trio Service Manual Download Page 77

Page: 77 / 82

System Alarm Prompts

Appendix

5 - 2

0070-10-0591-01

Trio™ Service Manual

ECG RA LEAD OFF

The RA lead wire of ECG is not
connected correctly

Check the connection of RA
lead wire

ECG C LEAD OFF

The C lead wire of ECG is not
connected correctly

Check the connection of C
lead wire

ECG F LEAD OFF

The F lead wire of ECG is not
connected correctly

Check the connection of F
lead wire

ECG L LEAD OFF

The L lead wire of ECG is not
connected correctly

Check the connection of L
lead wire

ECG R LEAD OFF

The R lead wire of ECG is not
connected correctly

Check the connection of R
lead wire

SpO

SENSOR OFF

SpO

sensor is not connected

correctly

Check the connection of
SpO

sensor

SpO

: INTERFERENCE

Noise detected on the pulse
signal prevents pulse
discrimination

Decrease patient motion.
Check sensor.

SpO

: PULSE SEARCH

Hardware settings are being
adjusted in order to
discriminate a pulse waveform

Wait several seconds for
saturation value to appear. If
it does not appear, do one of
the following:

•

Change to site where
pulse is stronger if patient
is vasoconstricted

•

Change or readjust
sensor if loose

SpO

: LOW PERFUSION

Patient perfusion is low

Check patient connection and
patient status

SpO

: TOO MUCH LIGHT

There is too much ambient room
light for the sensor to function
properly

Minimize the room light
around the patient. Check
sensor.

SpO

: UNRECOGNIZED

SENSOR

The sensor is not recognized by
the monitor

Replace the sensor with a
recommended sensor from
Customer Service.

SpO

: COMMUNICATION

ERROR

The monitor and the SpO

modules are not communicating
properly

Power the unit OFF/ON. If
problem persists, notify
hospital technician or
Customer Service.

SpO

: BOARD FAULT

MasimoSET® board failed to
operate properly

Notify hospital technician or
Customer Service.

SpO

: SENSOR FAULT

Defective Sensor

Replace sensor

TEMP SENSOR OFF

TEMP sensor is not connected
correctly

Check the connection of
TEMP sensor

IBP LEAD OFF

IBP cable is not connected
correctly

Check the connection of IBP
cable

ECG NOISE

Excessive interference appears
on the ECG signals

Check the connection of ECG
lead wires. Check the current
condition of the patient.

*XX ALM LMT ERR

The alarm limit of XX parameter
has inadvertently deviated from
standard range

If message does not clear
contact Customer Service.

PROBLEM/MESSAGE

REASON

SOLUTION

XX represents all the parameter modules in the system such as ECG, NIBP, SpO

, IBP module, etc.

Summary of Contents for Trio



















































































Search results

Summary of Contents for Trio

Reviews:

Related manuals for Trio

Brands by name

Popular brands

Mindray Trio, Service Manual

Search results

Summary of Contents for Trio

Reviews:

Related manuals for Trio

Brands by name

Popular brands