Mindray Trio Service Manual Download Page 34 | Manualshive

Page: 34 / 82

background image

Trio™ Service Manual

0070-10-0591-01

2 - 9

Calibration/Maintenance

Calibration and System Checks

Error Log:

This menu will display any system errors which may have occurred during
normal operation of unit.

SCROLL

or

PRINT

this information by selecting

the respective tiles

FIGURE 2-9

Error Log Menu*

Factory:

This menu allows the unit to be preconfigured at the factory. This menu is
enabled with an access code, 762718, and should only be accessed as
necessary by Customer Service Personnel or by trained Bio-medical
technicians after replacing defective modules as a result of unit repair.

The Factory menu allows for configuration of:

Serial Port:

This menu allows the user to configure the DIAP baud rate of the serial
output port. The choices are 9600 bps or 19200 bps.

• Language (English, Spanish*, French*, German*, Italian*, Chinese*).

• Module Options (ECG, Resp, SpO

2

, 1ch.Temp, 2ch.Temp*, NIBP, IBP,

Recorder).

Selections are enabled or disabled by checking or unchecking the box
which corresponds to each item in the menu.

NOTE:

IBP and 2ch. Temp should not be enabled
simultaneously.

*

Not available for domestic units.

«
...
32
33
34
35
36
...
»

Summary of Contents for Trio



















































































Reviews:

No comments

Related manuals for Trio

Brand: Napoleon Pages: 2

Brand: Raytheon Pages: 62

Sonopuls HD 4050

Brand: BANDELIN Pages: 48

Brand: Jackco Pages: 6

Brand: K-LASER Pages: 70

Brand: K-LASER Pages: 72

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: unios Pages: 2

SimMan 3G Trauma

Brand: laerdal Pages: 16

Brand: laerdal Pages: 16

Brand: laerdal Pages: 60

Brand: laerdal Pages: 4

Resusci Anne Simulator

Brand: laerdal Pages: 8

Nursing Baby VitalSim

Brand: laerdal Pages: 15

Brand: Pari Pages: 282

Brand: TC Electronic Pages: 14

Brand: Access Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands