Mindray Trio Service Manual Download Page 27

Page: 27 / 82

Calibration and System Checks

Calibration/Maintenance

2 - 2

0070-10-0591-01

Trio™ Service Manual

2.4

Calibration and System Checks

2.4.1

Device Appearance and Installation Checks

Inspect the

Trio

Monitor to ensure that:

• The outer housing of the device is clean and has no scratches or cracks

• When shaking the device, there are no loose components

• All keys are smooth and free for operation

• Labels are complete, sufficient and accurate

• Standard configuration is complete and all connectors are installed securely

2.4.2

Maintenance Menu

The

MAINTENANCE

menu provides access to all user operable calibration checks. It also

provides access to certain technical information and settings. To access the

MAINTENANCE

menu, turn the unit on, rotate the Navigator™ knob to highlight the

MENU

icon at the bottom of the screen and push the knob to select the

SYSTEM MENU

From the

SYSTEM MENU

, select

MAINTENANCE

FIGURE 2-1

Maintenance Menu DIAP units (S/N MC15000-XX and above)

Summary of Contents for Trio



















































































Search results

Summary of Contents for Trio

Reviews:

Related manuals for Trio

Brands by name

Popular brands

Mindray Trio, Service Manual

Search results

Summary of Contents for Trio

Reviews:

Related manuals for Trio

Brands by name

Popular brands