MIMAKI CG-FX SERIES Operation Manual Download

Page: 25 / 142

– 1.9 –

* When using three pinch rollers, arrange the middle pinch roller in the center

of the sheet. In case positioning to one-side, it may cause sheet slippage.

Or when using four pinch rollers (CG-160FX), positioning to equally.

* Move the pinch roller 3 to the retracted point located at the leftmost end of

its travel range in the case where the pinch roller 3 is not used for operation.

Or set to the number of pinch roller its using. (

Page 3.65)

If the pinch roller 3 is located at any position other the retracted point, the

device will not be able to perform the sheet detection.

Travel range of pinch rollers 1 and 2

CG-75FX

CG-130FX

CG-160FX

Travel range of PR2 (3)(4)

Travel range

of PR1

1308

〜

1570 (When using Pnch Roller 1, 2, 3 and 4)

1308

〜

1608 (When using Pnch Roller 1and 2)

Summary of Contents for CG-FX SERIES















































































































































Search results

Summary of Contents for CG-FX SERIES

Reviews:

Related manuals for CG-FX SERIES

Brands by name

Popular brands

MIMAKI CG-FX SERIES, Operation Manual

Search results

Summary of Contents for CG-FX SERIES

Reviews:

Related manuals for CG-FX SERIES

Brands by name

Popular brands