MIMAKI CG-FX SERIES Operation Manual Download

Page: 107 / 142

– 3.55 –

RotationSwitch the cut (plot) moving direction [ROTATION]

This function is used to specify the location of origin and direction of the axis of coordinates accord-

ing to the application software to be used.

Setting value

The device rotates the coordinate axis and relocates the origin at a time.

OFF

The device does not perform rotation of the coordinate axis.

After the sheet detection, the carriage will stop at the origin.

Axis of coordinates

The device has four different axis of coordinates according to how the sheet loading direction and

the angle of rotation of the coordinate axis determined by the rotating function are combined.

Rotating function: OFF Rotating function: ON

< 90

ROTATION >

The sheet is loaded on
the rear of the device.
Rotation: OFF

The sheet is loaded on
the front of the device.
Rotation: OFF

The sheet is loaded on
the rear of the device.
Rotation: ON

The sheet is loaded on
the front of the device.
Rotation: ON

< 0

ROTATION >

< 180

ROTATION >

< 270

ROTATION >

Summary of Contents for CG-FX SERIES















































































































































Search results

Summary of Contents for CG-FX SERIES

Reviews:

Related manuals for CG-FX SERIES

Brands by name

Popular brands

MIMAKI CG-FX SERIES, Operation Manual

Search results

Summary of Contents for CG-FX SERIES

Reviews:

Related manuals for CG-FX SERIES

Brands by name

Popular brands