– 5.2 –
Specifications of the main unit
Item
CG-75FX
CG-130FX
CG-160FX
Acceptable sheet width
mm
inch
mm
inch
mm
inch
90 ~ 1040
4 ~ 40
90 ~ 1580
4 ~ 62
90 ~ 1880
4 ~ 62
Effective cutting area *1
760mm x 51m
1300 mm x 51 m
1600 mm *2 x 51 m
Automatic Cutting area *3
885mm
1425 mm
1720 mm
Maximum speed *4
140 cm/s (At 45 degrees direction with the pen up.)
Speed setting
1 ~ 10 cm/s (in 1 cm/s steps), 10 ~ 40 cm/s (in 5 cm/s steps)
(cutting/plotting)
40 ~ 100 cm/s (in 10 cm/s steps)
Mechanical resolution
5
µ
m (excluding expansion/contraction due to film temperatures)
Program steps
25
µ
m, 10
µ
m (MGL-IIc), 100
µ
m, 50
µ
m (MGL-Ic)
Repeatability
±
0.2 mm (excluding expansion/contraction due to film temperatures)
Guaranteed range of
760mm x 10 m
1300 mm x 10 m
1300 mm x 10 m
accuracy (repeatability) *5
(depending on the specified film and cutting conditions)
Maximum pressure
400 g
Cutter
10 ~ 20 g (2 g step), 20 ~ 100 g (5 g step), 100 ~ 400 g (10 g step)
Pressure setting
Pin
10 ~ 20 g (2 g step), 20 ~ 100 g (5 g step), 100 ~ 400 g (10 g step)
Pen
10 ~ 20 g (2 g step), 20 ~ 100 g (5 g step), 100 ~ 150 g (10 g step)
Acceptable films
PVC sheets (0.2 mm thick or less), fluorescent sheets *6, reflective sheets *6,
laminated sheets (0.2 mm thick or less)
Acceptable sheet for pouncing
Paper (thickness: 0.06 to 0.13 mm) *7
Applicable tools
Cutters, water-ink ball-point pens, oil-ink ball-point pens, Commercial product for a
boll-point pen *8
Commands *9
MGL-IIc, MGL-Ic1
Interface
RS-232C, USB
Receiver buffer
30 MB standard (20Mb when the sorting function is effective.)
Operating environment
5 to 35
°
C, 35 to 75 % (Rh) Non-condensing
Power capacity
220/240 VAC, 170 VA or less
Outside dimensions (W)
1285 mm
1825 mm
2125 mm
(D)
610 mm
700 mm
(H)
1217 mm
Weight (With the legs attached)
50 kg
60 kg
66 kg
Noise *10
during discontinuous cutting (plotting) 49 dB (Absorption fan at low speed)
during continuous cutting (plotting) 60 dB (Continuous sounds)
*1: The maximum feeding length is restricted by the software to be used.
*2: When using four Pinch Rollers. In case using Pinch Roller 1 and Pinch Roller 2, the effective cutting
area is 1570 mm.
*3: The maximum speed may be restricted by the sheet size.
*4: The sheet width with the cut off function available.
*5: To achieve the guaranteed range of accuracy, the next page's requirements shall be satisfied.
*6: Provided that the blade specific to fluorescent sheets and the blade specific to reflective sheets are used.
*7: Pouncing tool intended specifically to pouncing shall be used.
*8: The commercial product between the 8 to 9 mm diameter. Accuracy and the quality of the image are
covered under warranty for the pen tip position differs according to the pen in use.
*9: When in use of the USB, the ESC type of the commands in the MGL-llc commands cannot be used.
*10: Standard measure of our products.
Summary of Contents for CG-FX SERIES
