background image

8

English

8

b.  Remove the retaining ring and pull out the pin from 

one of the blades.
NOTE: Take notice of the blade orientation so the
new blades can be installed the same way. The
blades should be oriented so the flat sides contact 
and the bevels face away from each other, like a
pair of scissors.

c.  Carefully remove the blade.
d.  Install the new blade in the same orientation.
e. Slide the pin through the blade and bracket.

Replace the retaining ring.

f.  Repeat steps a to e for the other blade.
g.  Insert the blade bolt.
h.  Thread the inner blade nut onto the blade bolt and 

tighten to 1 Nm.

i.

Thread the outer blade nut onto the blade bolt.
Holding the inner blade nut motionless, tighten
theouter blade nut to 11 Nm to lock the nuts
together.

Check that the cutting tools can move freely.
To avoid injury and damage, never immerse the tool, 
removable battery or charger in liquid or allow liquid to 
penetrate them.
The ventilation slots of the machine must be kept clear 
at all times.
The device contains hydraulic fluid. Hydraulic fluids 
pose a hazard to groundwater. Uncontrolled draining 
or improper disposal is punishable by law.
The device should be serviced every six to twelve 
months, depending on usage.
Service and repair work may only be carried out by 
authorised specialist workshops.
Use only MILWAUKEE accessories and MILWAUKEE 
spare parts. Should components need to be replaced 
which have not been described, please contact one 
of our MILWAUKEE service agents (see our list of 
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. 
Please state the Article No. as well as the machine 
type printed on the label and order the drawing at your 
local service agents.

BATTERIES

Battery packs which have not been used for some time 
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the 
performance of the battery pack. Avoid extended 
exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be 
kept clean.
For an optimum life-time, the battery packs have to be 
fully charged, after use.
To obtain the longest possible battery life remove the 
battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days: 

 

Store the battery pack where the temperature is
below 27°C and away from moisture 

 

Store the battery packs in a 30% - 50% charged
condition 

Every six months of storage, charge the pack as 

normal.
Do not dispose of used battery packs in the household 
refuse or by burning them. MILWAUKEE Distributors 
offer to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal 
objects (shor tcircuit risk).
Use only System M18 chargers for charging System 
M18 battery packs. Do not use battery packs from 
other systems.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous 
Goods Legislation requirements.
Transportation of those batteries has to be done in 
accordance with local, national and international 
provisions and regulations.

 

The user can transport the batteries by road
without further requirements.

 

Commercial transport of Lithium-Ion batteries
by third parties is subject to Dangerous Goods 
regulations. Transport preparation and transport 
are exclusively to be carried out by appropriately 
trained persons and the process has to be 
accompanied by corresponding experts.

When transporting batteries:

 

Ensure that battery contact terminals are protected 
and insulated to prevent short circuit.

 

Ensure that battery pack is secured against
movement within packaging.

 

Do not transport batteries that are cracked or leak.

Check with forwarding company for further advice.

 SYMBOLS

Please read the instructions carefully 
before starting the machine.

WARNING!
Risk of injury from ejected fragments

Always wear goggles when using the 
machine.

Danger of electric shock.

CAUTION! WARNING! DANGER!

Remove the battery pack before starting 
any work on the appliance.

Accessory - Not included in standard 
equipment, available as an accessory.

Summary of Contents for M18 HCC75







































Reviews: