Milwaukee FUEL SDS-MAX M18 FHM, Original Instructions Manual

Page: 17 / 100

15 15
GB
English
Do not machine any materials that present a danger to health (e.g.
asbestos).
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Switch the device off immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as doing
so could trigger a sudden recoil with a high reactive force. Determine
why the insertion tool stalled and rectify this, paying heed to the
safety instructions.
Possible causes can be:
• it is tilted in the workpiece to be machined
• breakage of the material to be used
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
Clamp your workpiece with a clamping device. Unclamped workpieces
can cause severe injury and damage.
Remove the battery pack before starting any work on the appliance.
WARNING
This device contains a button-type/coin cell lithium battery. A
new or used battery can cause severe internal burns and lead
to death in as little as 2 hours if swallowed or if it enters the body.
Always secure the cover on the battery compartment. If it does not
close securely, stop the device, remove the battery and keep it out of
reach of children.If you believe that someone has swallowed the
battery or that it has otherwise entered the body, seek immediate
medical attention.
OPERATION
Cold Starting
If this tool is stored for a long period of time or at cold temperatures, it
may not hammer initially because the lubrication has become stiff.
To warm up the tool
1. Insert and lock a bit or chisel into the tool.
2. Pull the trigger and apply force to the bit or chisel against a concrete
or wood surface for a few seconds. Release the trigger.
3. Repeat until the tool starts hammering. The colder the tool is, the
longer it will take to warm up.
ONE-KEY™
To learn more about the ONE-KEY functionality of this tool, please refer
to the Quick Start guide included with this product or go to http://
www.milwaukeetool.com/one-key
To download the ONE-KEY app, visit the App Store or Google Play
from your smart device.We considered the result to be within our
minimum acceptable performance level according to EN 301489-1/ EN
301489-17.And we will give the operation guidance to the customer
in user manual.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the
battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
but
For an optimum life-time, the battery packs have to be fully charged,
after use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged. For battery pack storage
longer than 30 days: Store the battery pack where the temperature
is below 27°C and away from moisture Store the battery packs in a
30% - 50% charged condition Every six months of storage, charge the
pack as normal.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System M18 chargers for charging System M18 battery packs.
Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
WARNING! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack
or charger in fluid or allow a fluid to flow inside them. Corrosive or
conductive fluids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., Can cause a short circuit.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations
that cause high current draw, the tool will stop for about 2 seconds
and then the tool will turn OFF. To reset, remove the battery pack from
the tool and replace it.
Under extreme circumstances, the internal temperature of the battery
pack could raise too much. If this happens, the fuel gauge will flash
until the battery pack cooled down. After the lights go off, the work
may continue.Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
Ensure that battery pack is secured against movement within
packaging.
Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice