6
Model:
Date of Purchase:
Distributor or Store Stamp:
RÈGLES DE SÉCURITÉ GÉNÉRALES
RELATIVES AUX OUTILS ÉLECTRIQUES
AVERTISSEMENT
Lire toutes les consignes
de sécurité, consignes, il
-
lustrations et spécifications fournies avec cet outil
électrique.
Ne pas suivre l’ensemble des règles et in
-
structions peut entraîner une électrocution, un incendie
ou des blessures graves.
Conserver les règles et les
instructions à des fins de référence ultérieure.
Le
terme «outil électrique» figurant dans les avertissements
ci-dessous renvoie à l’outil électrique à alimentation par
le réseau (à cordon) ou par batterie (sans fil).
SÉCURITÉ DU LIEU DE TRAVAIL
• Veillez à ce que l’aire de travail soit propre et
bien éclairée.
Le désordre et le manque de lumière
favorisent les accidents.
• Ne pas utiliser d’outils électriques dans des at
-
mosphères explosives, par exemple en présence
de liquides, gaz ou poussières inflammables.
Les outils électriques produisent des étincelles
risquant d'enflammer les poussières ou vapeurs.
• S’assurer que les enfants et les curieux se trouvent
à une bonne distance au moment d’utiliser un outil
électrique.
Les distractions peuvent causer une perte
de contrôle.
SÉCURITÉ
ÉLECTRIQUE
• Les fiches des outils électriques doivent correspon
-
dre à la prise secteur utilisée. Ne jamais modifier
la fiche, de quelque façon que ce soit. Ne jamais
utiliser d'adaptateurs de fiche avec des outils mis
à la terre.
Les fiches et prises non modifiées réduisent
le risque de choc électrique.
• Éviter tout contact avec des surfaces mises à
la terre comme des tuyaux, des radiateurs, des
cuisinières et des réfrigérateurs.
Le risque de choc
électrique est accru lorsque le corps est mis à la terre.
• Ne pas exposer les outils électriques à l'eau ou
l'humidité.
La pénétration d’eau dans ces outils accroît
le risque de choc électrique.
• Ne pas maltraiter le cordon d'alimentation. Ne
jamais utiliser le cordon d’alimentation pour trans-
porter l’outil électrique et ne jamais débrancher ce
dernier en tirant sur le cordon. Garder le cordon
à l'écart de la chaleur, de l'huile, des objets tran
-
chants et des pièces en mouvement.
Un cordon
endommagé ou emmêlé accroît le risque de choc
électrique.
• Pour les travaux à l’extérieur, utiliser un cordon
spécialement conçu à cet effet.
Utiliser un cordon
conçu pour l'usage extérieur réduit les risques de choc
électrique.
• Si l’utilisation d’un outil électrique est inévita
-
ble dans un endroit humide, utiliser une source
d’alimentation munie d’un disjoncteur de fuite de
terre.
L’utilisation d’un disjoncteur de fuite de terre
réduit le risque de choc électrique. sécurité individuelle
SÉCURITÉ
INDIVIDUELLE
• Rester attentif, prêter attention au travail et faire
preuve de bon sens lors de l'utilisation de tout outil
LIMITED WARRANTY USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted to the
original purchaser only to be free from defects in material and workmanship.
Subject to certain exceptions, MILWAUKEE will repair or replace any part on an
electric power tool which, after examination, is determined by MILWAUKEE to be
defective in material or workmanship for a period of five (5) years** after the date
of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE
factory Service Center location or MILWAUKEE Authorized Service Station,
freight prepaid and insured, is required. A copy of the proof of purchase should
be included with the return product. This warranty does not apply to damage
that MILWAUKEE determines to be from repairs made or attempted by anyone
other than MILWAUKEE authorized personnel, misuse, alterations, abuse, normal
wear and tear, lack of maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and service
to achieve best performance. This warranty does not cover repair when normal
use has exhausted the life of a part including, but not limited to, chucks, brushes,
cords, saw shoes, blade clamps, o-rings, seals, bumpers, driver blades, pistons,
strikers, lifters, and bumper cover washers.
*This warranty does not cover Air Nailers & Staplers; Airless Paint Sprayer;
Cordless Battery Packs; Gasoline Driven Portable Power Generators; Hand
Tools; Hoist – Electric, Lever & Hand Chain; M12™ Heated Gear; Reconditioned
Product; and Test & Measurement Products. There are separate and distinct
warranties available for these products.
**The warranty period for Job Site Radios, M12™ Power Port, M18™ Power
Source, Jobsite Fan and Trade Titan™ Industrial Work Carts is one (1) year from
the date of purchase. The warranty period for the Cables for the Drain Snake
is two (2) years from the date of purchase. The warranty period for the LED in
the LED Work Light and the LED Upgrade Bulb for the Work Light is the lifetime
of the product subject to the limitations above. If during normal use the LED or
LED Bulb fails, the part will be replaced free of charge.
Warranty Registration is not necessary to obtain the applicable warranty on a
MILWAUKEE power tool product. The manufacturing date of the product will be
used to determine the warranty period if no proof of purchase is provided at the
time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REM
-
EDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE
PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO
THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO
EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL,
CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, AT
-
TORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A
CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF
PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITA
-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY
IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE
DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PAR
-
TICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT
PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE
DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED
ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service section of
MILWAUKEE’s website www.milwaukeetool.com or call 1.800.SAWDUST
(1.800.729.3878) to locate your nearest service facility for warranty and non-
warranty service on a MILWAUKEE electric power tool.
LIMITED WARRANTY - MEXICO,
CENTRAL AMERICA & CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.
This warranty card covers any defect in material and workmanship on this
Power Tool.
To make this warranty valid, present this warranty card, sealed/stamped by the
distributor or store where you purchased the product, to the Authorized Service
Center (ASC). Or, if this card has not been sealed/stamped, present the original
proof of purchase to the ASC.
Call toll-free 1 800 832 1949 to find the nearest ASC, for service, parts, acces
-
sories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/stamped by
the distributor or store where you purchased the product, and there any faulty
piece or component will be replaced without cost for you. We will cover all freight
costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations:
a) When the product is used in a different manners from the end-user guide
or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modified or repaired by people not authorized by
TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized Service
Center to avoid electric risks.
SERVICE AND ATTENTION CENTER:
Presidente Masarik No.29 Piso 7
Col. Polanco V Sección
Miguel Hidalgo C.P.11560 Mexico, DF.
Ph. 52 55 4160-3547
IMPORTED AND COMMERCIALIZED BY:
TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.
Presidente Masarik No.29 Piso 7
Col. Polanco V Sección
Miguel Hidalgo C.P.11560 Mexico, DF.
