Miele WCE 670 Operating Instructions Manual Download

Page: 34 / 100

5. Adding detergent

Detergent dispenser drawer

Any detergent suitable for automatic
front loading washing machines can be
used with this appliance. Please
observe the instructions for use and
dosage on the detergent packaging.

Ensure that TwinDos dispensing is
deactivated.

Filling with detergent



Pull out the detergent drawer and add
detergents to the compartments.



Detergent for the pre-wash (divide
the total recommended amount as
follows: add ⅓ to compartment



and ⅔ to compartment



)



Detergent for the main wash and
soaking




Fabric softener, liquid starch, or
capsules

See “Detergent” for further information.

Adding fabric softener



Add fabric softener or liquid starch to
the



compartment.

Do not exceed

the maximum level mark.

It will be automatically dispensed in the
final rinse. At the end of the programme
a small amount of water remains in the
fabric softener



compartment.

If starching frequently, thoroughly
clean the dispenser compartment,
especially the siphon tube, regularly.

Summary of Contents for WCE 670





































































































Search results

Summary of Contents for WCE 670

Reviews:

Related manuals for WCE 670

Brands by name

Popular brands

Miele WCE 670, Operating Instructions Manual

Search results

Summary of Contents for WCE 670

Reviews:

Related manuals for WCE 670

Brands by name

Popular brands