Miele WCE 670 Operating Instructions Manual Download

Page: 14 / 100

Operating the washing machine

Control panel

The control field consists of a
display and various sensor controls.
The individual sensors are explained
in the following sections.

Display

The following values are shown in
the display and/or selected from it:
1. The temperature, spin speed and

time left for the selected wash
programme.

2. The individual values of the

selection lists for Extras and
settings.

Sensor controls



Values shown in the display can be
changed with the



sensors. The



sensor increases the value or

moves the selection list up; the



sensor decreases the value or
moves the selection list down.

OK sensor

Confirm selected values with the

sensor.

TwinDos sensors with options for
Whites and Colours

The TwinDos sensor is used for
deactivating and activating
automatic detergent dispensing.
Depending on the colour mix of your
load, you can control the detergent
combination by selecting

Whites

Colours

Further information can be found in
the “TwinDos” chapter.

Optical interface

For service technicians.

Summary of Contents for WCE 670





































































































Search results

Summary of Contents for WCE 670

Reviews:

Related manuals for WCE 670

Brands by name

Popular brands

Miele WCE 670, Operating Instructions Manual

Search results

Summary of Contents for WCE 670

Reviews:

Related manuals for WCE 670

Brands by name

Popular brands