Miele TDA 140 C Operating Instructions Manual Download Page 54

Page: 54 / 60

Programmable functions

Standby

To save energy, the display goes out

after 10 minutes and the indicator light

for the

Start

button starts flashing

slowly.

To come out of Standby mode:



Move the programme selector or

press

Start

. Neither will have any

effect if a programme is running.

Standby function is activated and the

indicator lights will go out after 10

minutes:

– if a programme is not selected after

the dryer has been switched on.

– after a programme has started.

They will, however come on for 10

minutes at the end of the programme or

the end of the anti-crease phase. The

buzzer (if selected) will sound for 10

minutes at the end of the programme.

Not in current programme (factory

default setting)

As described under "On".

However, indicator lights will stay on

when the programme has started and

remain visible during the programme.

Off

Indicator lights will stay on while the

dryer is switched on.

Follow steps (







...) to

programme and store in memory.
Before you begin, ensure that:

– The tumble dryer is switched off.
– The door is closed.
– The programme selector is pointing

Finish



Press

Start

and keep it pressed in

whilst carrying out steps







Switch the dryer on.



Wait until the indicator light for the

Start

button lights up constantly . . .



. . . and then release the

Start

button.



Turn the programme selector to

Gentle smoothing

The

Empty container

indicator light will

flash eight times.

Summary of Contents for TDA 140 C





























































Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands

Miele TDA 140 C, Operating Instructions Manual

Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands