Miele TDA 140 C Operating Instructions Manual Download Page 56

Page: 56 / 60

Programmable functions

Changing the function of the

airways indicator

Fluff should be removed after drying.

The

Clean out airways

indicator light

will remind you to clean the filters

when a certain amount of fluff has

collected in them. You can decide at

what level of fluff this reminder should

be given.

You will have an idea of which option to

select after a few drying programmes.
Certain faults can also cause this

indicator light to come on at other

times.

Follow steps (







...) to

programme and store in memory.
Before you begin, ensure that:

– The tumble dryer is switched off.
– The door is closed.
– The programme selector is pointing

Finish



Press

Start

and keep it pressed in

whilst carrying out steps







Switch the dryer on.



Wait until the indicator light for the

Start

button lights up constantly . . .



. . . and then release the

Start

button.



Turn the programme selector

Woollens

The

Empty container

indicator light will

flash slowly once.

The option selected will be displayed

by a

number

which will alternate with





The

Clean out airways

indicator

light is deactivated



The

Clean out airways

indicator

light only comes on when there is

a heavy build-up of fluff

(The

Clean out airways

indicator light

will also flash once)



Factory default setting

(The

Clean out airways

indicator light

will also flash twice)



The

Clean out airways

indicator

light comes on when there is a

slight build-up of fluff

(The

Clean out airways

indicator light

will also flash three times)



Pressing the

Start

button switches

between the options.



Switch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:



Carry out steps







Switch the dryer off after checking.

Summary of Contents for TDA 140 C





























































Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands

Miele TDA 140 C, Operating Instructions Manual

Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands