Miele TDA 140 C Operating Instructions Manual Download Page 52

Page: 52 / 60

Programmable functions

Altering the standard drying

level in the"Automatic plus"

programme

The drying level for this programme is

set to the standard

Normal

level. You

have the option of changing the drying

level to

Hand iron

(damper than

Normal) or to

(drier than

Normal).

Follow steps (







...) to

programme and store in memory.
Before you begin, ensure that:

– The tumble dryer is switched off.
– The door is closed.
– The programme selector is pointing

Finish



Press

Start

and keep it pressed in

whilst carrying out steps







Switch the dryer on.



Wait until the indicator light for the

Start

button lights up constantly . . .



. . . and then release the

Start

button.



Turn the programme selector to

Cottons Hand iron

The

Empty container

indicator light will

flash six times.

The option selected will be displayed

by a

number

which will alternate with





Standard setting -

Hand iron



Factory default setting

(The

Clean out airways

indicator light

will also flash once)



Standard setting will be

(The

Clean out airways

indicator light

will also flash twice)



Pressing the

Start

button switches

between the options.



Switch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:



Carry out steps







Switch the dryer off after checking.

Summary of Contents for TDA 140 C





























































Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands

Miele TDA 140 C, Operating Instructions Manual

Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands