Miele TDA 140 C Operating Instructions Manual Download Page 31

Page: 31 / 60

Problem solving guide

Problem

Cause and remedy

The

Start

indicator light

flashes slowly and the

display is dark.

The dryer is in standby mode. This is a normal

function and does not indicate a fault.



See "Standby" in "Programmable functions".

The

Clean out airways

indicator light comes on

at the end of a

programme.

There is a build-up of fluff in the airways.



Clean the fluff filters



Clean the condenser unit



Open and close the door while the dryer is

switched on. The indicator light will go out.

The programme is

cancelled and the

Clean

out airways

indicator

light comes on.

An excessive amount of fluff has built up.



Clean the fluff filters and condenser unit.



Open and close the door while the dryer is

switched on. The indicator light will go out.

Bars flash in the display

at the end of a

programme:



...



...



...

The programme has finished but the laundry has not

yet cooled down.



Either remove the laundry and spread it out to cool

down or leave it in the tumble dryer to cool down

during the cooling phase.



lights up

The programme selector has been moved.



Select the original programme. The time remaining

will appear in the display again.

Summary of Contents for TDA 140 C





























































Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands

Miele TDA 140 C, Operating Instructions Manual

Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands