Miele TDA 140 C Operating Instructions Manual Download Page 53

Page: 53 / 60

Programmable functions

Extending the cooling down

time

The cooling down phase which takes

place before the end of a programme

can be lengthened in two stages if

required. This cools the garments

down even more.

Follow steps (







...) to

programme and store in memory.
Before you begin, ensure that:

– The tumble dryer is switched off.
– The door is closed.
– The programme selector is pointing

Finish



Press

Start

and keep it pressed in

whilst carrying out steps







Switch the dryer on.



Wait until the indicator light for the

Start

button lights up constantly . . .



. . . and then release the

Start

button.



Turn the programme selector to

Cottons Machine iron

The

Empty container

indicator light will

flash seven times.

The option selected will be displayed

by a

number

which will alternate with





Factory default setting



The cooling down time will be

extended by five minutes

(the

Clean out airways

indicator light

will also flash once)



The cooling down time will be

extended by ten minutes

(the

Clean

out airways

indicator light will also

flash twice)



Pressing the

Start

button switches

between the options.



Switch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:



Carry out steps







Switch the dryer off after checking.

Summary of Contents for TDA 140 C





























































Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands

Miele TDA 140 C, Operating Instructions Manual

Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands