Miele TDA 140 C Operating Instructions Manual Download Page 30

Page: 30 / 60

Problem solving guide

With the help of the following notes minor faults in the performance of the

appliance, some of which may result from incorrect operation, can be put right

without contacting the Service Department.



Repair work to electrical appliances must only be carried out by a suitably

qualified person in strict accordance with current local and national safety

regulations. Repairs and other work by unqualified persons could be

dangerous. The manufacturer cannot be held liable for unauthorised work.

Check and fault messages

Problem

Cause and remedy

The

Empty container

indicator lights up. The

programme is

cancelled, the buzzer

sounds.

The condensed water container is full or there is kink

in the drain hose.



Empty the container.



Check the drain hose.



Open and close the door while the dryer is

switched on. The indicator light will go out.

The programme is

cancelled.

The buzzer may sound

and the

Clean out

airways

Empty

container

indicator

flashes.

No obvious cause.



Switch the dryer off and then on again.



Start a programme.

If the programme is cancelled again and a fault

message appears, there is a fault. Contact Miele

service.

The programme is

cancelled,



lights up

This is not a fault.

In some programmes, if the drum has been

underloaded or is empty, the programme will be

cancelled. This can also happen if the items are

already dry.



Open and close the door to resume drying.



Dry individual items using the

Warm air

timed

drying programme.

Summary of Contents for TDA 140 C





























































Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands

Miele TDA 140 C, Operating Instructions Manual

Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands