Miele TDA 140 C Operating Instructions Manual Download Page 13

Page: 13 / 60

Operating the tumble dryer

Control panel

Display

h min

See the following page for more information.

Check / fault indicator lights

See "Problem solving guide"

The

check light is also used by service technicians to run diagnostic

checks on your tumble dryer and may be used to update programming data in

the future.

Start

button

Press the Start button to start a programme

The Start indicator light will flash as soon as the programme can be started. It

lights up constantly once the programme has started.

Programme selector

The programme selector can be turned clockwise or anti-clockwise.

On/Off button



To switch the appliance on or off.



or the programme duration will light up as confirmation that the tumble dryer

has been switched on.

Door

button

Pressing this button will open the door even when the appliance is not

switched on at the mains.

Summary of Contents for TDA 140 C





























































Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands

Miele TDA 140 C, Operating Instructions Manual

Search results

Summary of Contents for TDA 140 C

Reviews:

Related manuals for TDA 140 C

Brands by name

Popular brands