Miele PWM 906 Operating And Installation Instructions Download Page 79

Page: 79 / 100

Supervisor level

Opening the Supervisor level



Switch on the washing machine.



11:02







Programs

Favourites

Supervisor

Help



Touch the

Supervisor



sensor

control.

The display will switch to the

Supervisor

level

menu.

Code-based access

The Supervisor level is accessed using
a code.

The code is

000

(factory default).

Changing the code

You can alter the Supervisor level
access code to protect the washing
machine from unauthorized access.

Please inform Miele Service if you
have forgotten your new code. Miele
Service will have to reset the code.
Make a note of your new code and
store it in a safe place.

Closing the settings menu



Touch the



sensor control.

The display will then go back to the
previous menu level.



Touch the



sensor control.

The display will change to the main
menu.

Summary of Contents for PWM 906





































































































Search results

Summary of Contents for PWM 906

Reviews:

Related manuals for PWM 906

Brands by name

Popular brands

Miele PWM 906, Operating And Installation Instructions

Search results

Summary of Contents for PWM 906

Reviews:

Related manuals for PWM 906

Brands by name

Popular brands