Miele KWT 6112 iG ed/cs Operating And Installation Instructions Download Page 41 | Manualshive

Page: 41 / 64

background image

Cleaning and care

41

Cleaning the ventilation gaps

A build-up of dust will increase the en-
ergy consumption of the appliance.



The ventilation gaps should be
cleaned on a regular basis with a
brush or vacuum cleaner (e.g. use the
dusting brush for Miele vacuum
cleaners)

Cleaning the door seal

Do not use any grease or oil on the
door seal as these will cause the seal
to deteriorate and become porous
over time.



The door seal should be cleaned reg-
ularly with clean water, and then
wiped dry with a soft cloth.

After cleaning



Replace all shelves and accessories
in the wine conditioning unit.



Reconnect to the mains and switch
the wine conditioning unit back on.



Place the wine bottles back in the
wine conditioning unit and close the
door.

«
...
39
40
41
42
43
...
»

Summary of Contents for KWT 6112 iG ed/cs

































































Reviews:

No comments

Related manuals for KWT 6112 iG ed/cs

Brand: Danby Pages: 21

Brand: Silhouette Pages: 20

Brand: Silhouette Pages: 34

Brand: SCHOLTES Pages: 36

Brand: Oceanic Pages: 22

Brand: GE Pages: 16

Brand: Black & Decker Pages: 12

Brand: U-Line Pages: 50

Brand: La Sommeliere Pages: 47

Brand: BORETTI Pages: 36

Brand: Southern Enterprises Pages: 12

Brand: Micasa Pages: 9

Brand: Klarstein Pages: 41

Brand: Klarstein Pages: 56

Brand: Klarstein Pages: 56

Brand: Klarstein Pages: 64

Brand: Klarstein Pages: 84

Brand: Kucht Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands