Miele KWT 6112 iG ed/cs Operating And Installation Instructions Download Page 49 | Manualshive

Page: 49 / 64

background image

Noises

49

Normal noises

What causes them

Brrrrr ...

A humming noise is made by the motor (compressor). This
noise can get louder for brief periods when the motor switches
on.

Blubb, blubb ...

A gurgling noise can be heard when coolant is circulating
through the pipes.

Click ...

Clicking sounds are made when the thermostat switches the
motor on and off.

Sssrrrrr ...

On multi-zone wine conditioning units you can sometimes just
hear the sound of the fan inside the appliance.

Crack ...

A cracking sound can be heard when material inside the wine
conditioning unit expands.

Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.

Noises that you
can easily rectify

Possible cause

Remedy

Rattling, vibrating

The wine conditioning unit is
uneven.

Realign the wine condition-
ing unit using a spirit level,
by raising or lowering the
screw feet underneath the
appliance.

Shelves are unstable or stick-
ing.

Check all removable items
and refit them correctly.

Bottles or containers are
touching each other.

Separate them.

The transport cable clips are
hanging loose at the back of
the appliance.

Remove the cable clips.

«
...
47
48
49
50
51
...
»

Summary of Contents for KWT 6112 iG ed/cs

































































Reviews:

No comments

Related manuals for KWT 6112 iG ed/cs

Brand: Dacor Pages: 8

Brand: Dacor Pages: 16

Brand: Smith & Hanks Pages: 14

Brand: La Sommeliere Pages: 26

Brand: Ariston Pages: 52

Brand: Baumatic Pages: 32

Brand: Haier Pages: 36

Brand: Haier Pages: 48

Brand: Caple Pages: 14

Brand: Kadeka Pages: 16

Brand: Viking Pages: 1

Brand: Viking Pages: 5

Brand: Polar Electro Pages: 12

Brand: Polar Electro Pages: 56

Brand: Avantgarde Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands