Miele KWT 6112 iG ed/cs Operating And Installation Instructions Download Page 17 | Manualshive

Page: 17 / 64

background image

Guide to the appliance

17

Door opening mechanism

The Push2open system on your wine
conditioning unit makes it easy to open
the door. The door on your wine unit is
sensitive to pressure.

The Push2open system is deactivated
at the factory. The system has to be
activated by touching the On/Off
sensor once the appliance has been
installed in the niche (see "Switching
on and off").

To open the door



Risk of damage!

To avoid damage to the door open-
ing mechanism:
Do not obstruct the appliance door
while it is opening. Do not push in or
hold onto the door catch while the
door is closing.



Press briefly

against the top left

hand side of the appliance door

and then release it. The door will then
open a little way automatically.



Then pull the door fully open.



Risk of damage!

Do not subject the door to any pres-
sure when it is open. Do not place
anything on it whilst open.

To protect against inadvertent open-
ing: if you do not pull the door open, it
will close again by itself after approx. 3
seconds.

To close the door



Push the door shut.

Please be aware that using magnets in
front of the wine unit door can cause it
to open by mistake. This is caused by
the door closing mechanism on the
wine unit.

«
...
15
16
17
18
19
...
»

Summary of Contents for KWT 6112 iG ed/cs

































































Reviews:

No comments

Related manuals for KWT 6112 iG ed/cs

Brand: Qlima Pages: 124

Brand: Saivod Pages: 32

Brand: Lamona Pages: 20

Brand: Magic Chef Pages: 24

Brand: Frigidaire Pages: 9

Vinage Keeper 500

Brand: shanghai koolspace Pages: 23

Brand: Haier Pages: 110

Brand: Thor Kitchen Pages: 10

Brand: Sandstrom Pages: 72

WINEMASTER C50S

Brand: Fondis Pages: 33

WINEMASTER C50 IN

Brand: Fondis Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands